JBJ Auto Top Off Pump: Setup, Calibration and Maintenance Steps
Learn how a jbj auto top off pump works, how to set it up and calibrate the float switch, and how to keep your reef tank's water level stable.
Updated November 2026
A jbj auto top off pump replaces water lost to evaporation so your reef tank’s salinity stays steady and your livestock stays safe. In this guide you will learn how the system works, how to install it correctly, how to calibrate the sensor, and how to maintain it so it never lets your sump run dry or overflow. The steps apply to most JBJ-style float-switch ATO kits, though you should always check the manual that came with your unit.
How a JBJ Auto Top Off Pump Works
Most JBJ units use a simple sensing arrangement. A reservoir of fresh water (RO/DI water, never tap water) sits above or beside your sump. When the water level in the sump drops, a float or sensor signals the pump to run, moving fresh water in until the level returns to its set point. When the level rises back up, the sensor cuts power and the pump stops.
Because the pump only adds water and does not remove salt, evaporation leaves the salt behind. That is why top-off water must be fresh water. Adding saltwater or tap water will gradually shift your salinity or introduce contaminants.
Key components
- Reservoir: a food-safe container holding fresh RO/DI water.
- Pump head: the submersible or inline pump that moves water.
- Sensor or float: the component that detects the sump water level.
- Controller or power block: the electronics that switch the pump on and off.
- Tubing and fittings: the delivery line from reservoir to sump.
Before You Install: Checklist and Tools
Gather everything before you start. Working through an installation with a half-finished setup is how mistakes happen.
- The JBJ kit, including the pump, sensor, tubing and power supply.
- A reservoir sized for at least two to three days of evaporation for your tank.
- RO/DI water, freshly produced and tested for TDS near 0 ppm.
- A GFCI outlet or power strip with a drip loop for the cord.
- Zip ties, a marker and a small towel for drips.
- A marine-safe silicone or tubing clamp if your mounting requires it.
Step-by-Step Installation
Step 1: Choose the mounting location
Place the reservoir above the sump’s maximum water line so that gravity or the pump can deliver water without air-locking. Keep the sensor in the sump’s main chamber, away from the return water flow and protein skimmer bubbles, which cause false readings. Mount it in still water where the surface level is representative of the whole sump.
Step 2: Position the sensor and float
Attach the sensor so it sits at the level you want to maintain. Most owners set the on-point roughly a quarter inch below the sump’s full level and the off-point just at the target. Leave enough room for the float to move freely without catching on the sump walls, heater, or return plumbing.
Step 3: Connect the tubing and pump
- Cut the tubing to a clean, straight length with no kinks.
- Connect the pump outlet to the tubing and route it to the sump.
- Secure the tubing outlet above the water line so it cannot siphon back into the reservoir.
- Confirm the pump intake sits fully submerged in the reservoir.
Step 4: Power the system
Plug the controller into a GFCI-protected outlet. Route the cord so water cannot run down it into the outlet. Place a drip loop below the outlet so any condensation falls away from the plug.
Calibrating the Sensor
Calibration determines whether your system adds water at the right time. Poor calibration is the most common reason an ATO overfills or runs constantly.
- Let the sump settle to its normal operating level with the return pump running.
- Mark the current level with a piece of tape on the sump wall.
- Adjust the sensor so the float or probe rests at the target point.
- Manually lower the level slightly (or wait for evaporation) and confirm the pump starts at the intended on-point.
- Let the pump run and confirm it stops at the target without overshooting.
Owners often report that a second check after 24 hours helps catch any drift caused by surface film or salt creep on the sensor.
Maintenance Schedule
| Task | Frequency | Why it matters |
|---|---|---|
| Check reservoir level and water quality | Weekly | Prevents the pump running dry |
| Clean sensor and float | Every 2 weeks | Removes film that causes false readings |
| Inspect tubing and fittings | Monthly | Catches leaks and kinks early |
| Test reservoir TDS | Every 2 to 4 weeks | Confirms top-off water stays fresh |
| Recalibrate the sensor | After any sump change | Keeps the water level accurate |
Common Mistakes
- Using tap water or saltwater in the reservoir. Fresh water is the only safe top-off choice for a reef.
- Mounting the sensor near the return outlet. Turbulence creates false readings and erratic cycling.
- Setting the reservoir too low. Gravity feed stops working and the pump can run dry.
- Skipping the GFCI. Water near electrical connections is a shock risk. Use a GFCI outlet and a drip loop.
- Ignoring the reservoir. An empty reservoir means the tank has no protection against evaporation.
- Forgetting a backup. Consider a secondary high-level shutoff or a simple float switch as a safeguard against sensor failure.
Tips for Reliable Operation
- Size your reservoir to last at least two days so a power outage or failure does not leave you with a dry sump.
- Use a dedicated RO/DI unit that produces water with near-zero TDS.
- Label the reservoir with the date you last filled it.
- Note the on and off set points in your maintenance log so you can spot drift early.
Recommended gear
These items help with a clean, reliable installation. Look for the product types listed rather than a specific model if you already have a compatible unit.
- Food-safe top-off reservoir: A sealed container sized for two to three days of evaporation keeps fresh water ready and protected from contaminants. View on Amazon
- GFCI power strip: A protected outlet strip reduces shock risk where water and electricity meet near the sump. View on Amazon
- TDS meter: A handheld TDS meter lets you confirm your RO/DI top-off water is near zero before it reaches the tank. View on Amazon
- Marine-safe silicone sealant: Useful for securing mounts and sealing small leaks in reservoir connections. View on Amazon
For more troubleshooting and model-specific guidance, see JBJ Auto Top Off Not Working: Troubleshooting Steps That Fix It and 6 Best JBJ Auto Top Off Systems for Reef Tanks (2026). If you are comparing sensor types before buying, 4 Best JBJ Auto Top Off Sensors for Reef Tanks (2026) covers the options. Owners upgrading from a basic setup may also find Top 7 Auto Top Offs for Nano Tank Systems with Reliable Sensing useful for context.
FAQ
Can I use tap water in a jbj auto top off pump?
No. Tap water contains dissolved minerals, chlorine and other contaminants that build up in a reef tank over time. Use RO/DI water with a TDS reading close to zero.
Why does my JBJ ATO keep running?
Usually the sensor is reading a level that never reaches the off point, often because of film on the float, a sensor placed in turbulent water, or a leak in the sump. Clean the sensor, check for leaks, and recalibrate.
How often should I refill the reservoir?
Refill whenever the level drops toward the bottom third, and make sure it always holds at least two days of evaporation for your tank.
Should I add salt to the top-off water?
No. Top-off water should be fresh. Salt stays in the tank when water evaporates, so adding salt to the reservoir would raise salinity over time.
What should I do if the pump runs dry?
Turn the system off, refill the reservoir, and prime the pump if the manual calls for it. Check for air in the line. Consider adding a dry-run protection safeguard or a secondary shutoff.
How do I know the sensor is calibrated correctly?
Mark the sump level, lower it slightly, and confirm the pump starts at the intended point and stops at the target without overshooting. Recheck after 24 hours.
How often should I clean the sensor?
Every two weeks is a common routine, or sooner if you notice the pump cycling oddly. Salt creep and film can cause false readings.
Is a jbj auto top off pump safe for nano tanks?
Yes, provided the reservoir, tubing and sensor are sized for the smaller sump and you calibrate the set points carefully, since small level changes matter more in nano systems.
Conclusion
A well-installed jbj auto top off pump keeps your reef’s water level and salinity stable without constant attention. Use fresh RO/DI water, mount the sensor in still water, calibrate carefully, and keep up with a simple maintenance schedule. For electrical and water-safety questions, consult a qualified electrician or your aquarium retailer.
Ready to choose one?
