We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

DIY Sump for Aquarium: A Step-by-Step Build Guide for Reef Tanks

Learn how to build a DIY sump for aquarium use, from choosing a container and plumbing the overflow to sizing the return pump for a reef tank.

Updated November 2026

A DIY sump for aquarium use is a separate tank plumbed beneath your display, and it gives you extra water volume, room for equipment, and a place to hide heaters and skimmers. In this guide you will plan the sump size, select a container, plumb the overflow and return, and avoid the mistakes that cause flooding or pump failure. Most builds can be finished in a weekend once the parts are on hand.

Plan the Sump Size and Layout

Start with the main tank’s volume and aim for a sump holding roughly 20 to 30 percent of the display’s total water. A 75-gallon reef, for example, works well with a sump in the 20- to 25-gallon range. Make sure the sump fits the stand with at least two inches of clearance above the water line, so splashes and overflow noise stay contained.

Shopping for one? See our guide: 5 Best Sump Tanks for Aquarium Setups Compared (2026).

Sketch the layout before you cut anything. Place the skimmer in the main chamber, the heater in a separate chamber or a protected corner, and the return pump in the last chamber. Leave room to reach every component for cleaning.

Build the Chambers and Overflow

Most DIYers use acrylic or glass panels joined with aquarium-grade silicone. Dividers should sit about one inch below the water line so water can flow over them without siphoning. Use baffles or a filter sock if you want to trap detritus before it reaches the pump.

The overflow drain is the most important part of the build. It should be sized to handle more flow than your return pump delivers, so the system never backs up. A common rule of thumb is to size the drain for at least 1.5 times the pump flow.

Plumb the Return and Test for Leaks

Connect the return pump to a bulkhead or union in the sump floor or wall, then run the line up to the display with a check valve or a gate valve to control flow. Position the return outlet to create gentle circulation rather than a direct jet at the glass.

Before adding livestock or salt, fill the system with fresh water and run it for at least 24 hours. Check every fitting, bulkhead and seam. Mark the water line so you can spot any drop over the following days.

Checklist for Your DIY Sump Build

  1. Confirm sump volume and stand clearance
  2. Cut or purchase tank panels and dividers
  3. Install bulkheads for the drain and return
  4. Seal all seams with aquarium-safe silicone and allow full cure time
  5. Plumb overflow, return line and valves
  6. Run a 24-hour leak test with fresh water
  7. Add salt and livestock only after the system is stable

Common Mistakes

  • Undersizing the overflow, which leads to flooding when the pump runs harder.
  • Using non-aquarium silicone, which can release compounds harmful to corals and fish.
  • Placing the return pump where it pulls in air, causing noise and reduced flow.
  • Skipping the leak test and discovering problems after the display is full of saltwater.
  • Forgetting to plan access for cleaning the skimmer and pump.
  • Aquarium-grade silicone helps you seal panels and bulkheads safely. Look for products labeled as safe for reef or marine use. View on Amazon
  • Bulkhead fittings let you pass drain and return lines through the sump wall cleanly. View on Amazon
  • Ball valves give you control over return flow and make maintenance easier. View on Amazon

FAQ

How big should a DIY sump be?

Many reef keepers aim for a sump holding about 20 to 30 percent of the display volume. Leave enough room for the skimmer, heater and return pump without overcrowding.

Can I use regular silicone for a sump?

No. Use 100 percent silicone labeled safe for aquariums, since some household sealants release compounds that harm livestock.

How do I know if my overflow is sized correctly?

The overflow should handle more flow than the return pump, with room to spare. Test it by running the pump at full speed and watching for any water rising above the sump’s top edge.

Conclusion

A well-planned DIY sump gives your reef stable water volume and a clean place for equipment. Take time on the overflow sizing and leak test, since those steps prevent most failures. With a careful build, your sump will serve the system reliably for years.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Audrey Hayes
Audrey Hayes

Audrey Hayes writes reviews and buying guides for My Reef Aquarium.