Aquarium Sump Set Up: A Step-by-Step Reef Guide for Beginners
Learn how to plan, place, plumb and test an aquarium sump set up for a reef tank, with checklists, a sizing table and common mistakes to avoid.
An aquarium sump set up adds a separate tank below or beside your display, holding extra water, heaters, skimmers and filter media out of sight. Done right, it gives you more water volume, stable temperatures and room for equipment that keeps a reef healthy. This guide walks you through sizing, placement, plumbing, startup and the mistakes that cause flooded floors and dead pumps.
What a Sump Does and Why Reefers Use One
A sump is a secondary vessel plumbed to the main display, usually through an overflow box in the display tank. Water drains by gravity into the sump, where a return pump lifts it back up to the display. The display stays clean and uncluttered, while the sump hides protein skimmers, heaters, reactors, dosing lines and media baskets.
Most reef keepers choose a sump because it adds water volume without changing the look of the display, dilutes nutrient swings and makes maintenance far easier. Before you buy anything, read through the 5 Best Sump Tanks for Aquarium Setups Compared (2026) comparison to see the common designs and sizes available.
Plan Your Layout Before You Buy
Good planning prevents the most expensive problems. Measure the space under or beside the display, then decide where every piece will sit.
- Measure the cabinet or stand. Record the interior height, width and depth. Leave at least 2 inches of clearance on every side for airflow, plumbing and access.
- Choose a sump size. A common guideline among reef keepers is a sump holding roughly 20 to 30 percent of the display volume, though larger is often easier to keep stable.
- Plan the equipment. List your skimmer, heater, return pump, refugium or reactor, and any ATO (auto top-off) components. Confirm each one physically fits the sump compartments.
- Plan the water level. The sump must be large enough that the return pump never runs dry, even when the display drops from evaporation or the ATO fails.
Sizing Reference
| Display Size | Typical Sump Range | Common Equipment Layout |
|---|---|---|
| 10 to 20 gallons (nano) | 5 to 10 gallons | Small skimmer, heater, return pump |
| 40 to 75 gallons | 15 to 30 gallons | Hang-on or internal skimmer, refugium section, heater |
| 90 to 150 gallons | 30 to 60 gallons | External skimmer, multiple chambers, reactor space |
These ranges are general planning figures, not hard rules. Check the sump manufacturer’s specifications for working capacity, since the usable volume is often less than the stated total.
Gather Tools and Supplies
Having everything on hand before you start cuts the setup time in half and reduces the chance of leaks from improvised fittings.
- Sump tank with baffles or a pre-drilled overflow
- Bulkhead fittings and matching gaskets (usually 1 inch for overflow lines)
- Flexible vinyl tubing or rigid PVC, depending on your plumbing plan
- Gate valves or ball valves for flow control
- Return pump rated for your target flow and head height
- Plumbing tape, silicone or aquarium-safe sealant as the manufacturer specifies
- Level, tape measure and marker
- Drip tray or absorbent pad under the sump
- Reverse osmosis/deionized water and marine salt for the initial fill
Step-by-Step Sump Installation
Step 1: Set Up the Stand and Sump Location
Place the sump on a level, load-bearing surface. Water weighs about 8.3 pounds per gallon, so a 30-gallon sump filled with water adds roughly 250 pounds before the stand, equipment and rock are counted. Confirm the cabinet and floor can handle that load. Use a level to check the sump surface, because an uneven base can stress the glass seams.
Step 2: Install Bulkheads and Plumbing Lines
Install the bulkhead fittings in the overflow box and the sump walls. Tighten them evenly, following the manufacturer’s torque guidance, and avoid overtightening plastic threads. Route the drain line from the overflow to the sump, and the return line from the pump back to the display. Keep the drain line slightly sloped so air bubbles move toward the sump rather than collecting in the pipe.
Step 3: Mount the Return Pump and Install Valves
Place the return pump in the sump’s return chamber, on a pad or pump stand that keeps it off the bottom. Install a gate or ball valve on the return line so you can fine-tune flow. Position the pump intake above the sump floor to avoid pulling in detritus. Many reef keepers use a pump with a flow-control valve so noise and flow can be adjusted after startup.
Step 4: Install Heater, Skimmer and Other Equipment
Mount the heater in the sump, not the display, so it is out of sight and easy to service. Place it in a flow area so it heats evenly. For heater sizing, see 100 W Aquarium Heater: How to Size, Set and Install It Safely. Secure the skimmer on its own chamber, and confirm its intake sits below the waterline when the sump is at normal level.
Step 5: Add Water and Test for Leaks
Fill the sump slowly with pre-mixed saltwater, then start the return pump. Watch every fitting and seam for at least 24 hours. Check the gaskets after the first full day, because thermal expansion can loosen a bulkhead. Only add livestock after the system runs leak-free and stable.
Step 6: Calibrate Water Level and Flow
Adjust the return valve until the overflow runs quiet, with no gurgling or siphon noise. Set the water level so the display stays full with a comfortable buffer in the sump. Test a power outage scenario: unplug the pump and confirm the overflow drains without overflowing the display.
Startup Checklist
- Sump and display filled with mixed saltwater, salinity checked with a refractometer
- All bulkheads inspected for drips after 24 hours
- Return pump running quietly at the target flow
- Heater set and verified with a separate thermometer
- Skimmer producing foam once the system has settled
- Auto top-off reservoir filled and tested
- Leak tray and drip protection in place
- Backup plan for power outages, including a battery-backup or outage-safe valve if your setup needs one
Common Mistakes to Avoid
- Undersizing the sump. A sump that is too small lets salinity and temperature swing quickly and leaves no buffer when the return pump fails.
- Placing the return pump too high. Excess head height reduces flow and can cause the pump to run dry during a power interruption.
- Skipping the outage test. A sump that works on a normal day can overflow the display when power drops. Test every time you change plumbing.
- Using the wrong fittings. Mismatched bulkheads and gaskets are a frequent source of slow leaks.
- Forgetting access. Equipment that is hard to reach gets neglected. Leave room for hands and tools.
- Overloading the cabinet. Confirm the stand can support the full water weight plus equipment.
Tips for a Quieter, More Reliable Setup
- Use a sump lid or cover to cut evaporation and reduce splashing noise.
- Place a foam or rubber mat under the sump to dampen vibration.
- Label every valve and line so future maintenance is quick and safe.
- Keep spare gaskets and a spare heater on hand.
- Check and clean the skimmer collection cup on a regular schedule.
Recommended gear
A few supplies make a sump easier to install and safer to run. Look for products that match your sump size and pump rating.
- Eheim Jager Aquarium Heater: A submersible heater that can be mounted inside the sump, keeping the display free of visible equipment. See Eheim Jager Aquarium Heater Review: Pros and Cons for details. View on Amazon
- Flipper Aquarium Algae Magnet Cleaner: Useful for keeping display glass clear after the sump is running. View on Amazon
- Digital refractometer: Helps you check salinity accurately in both display and sump. View on Amazon
- Aquarium-safe sealant: For use only where the manufacturer allows it, to secure fittings and close small gaps. View on Amazon
FAQ
How big should an aquarium sump be?
A common planning range is 20 to 30 percent of display volume, but many reef keepers go larger for stability. The right size depends on your equipment and how much buffer you want for power outages.
Can a sump go under the display?
Yes. Most stands are built with a sump bay below the display. Confirm the cabinet has enough height and that you can reach the equipment comfortably. A related read: Nano Reef Tank Set Up: A Step-by-Step Guide for Beginners.
Where should the return pump go?
Place it in the return chamber on a pad or stand, with the intake above the sump floor. Keep head height as low as practical to maintain flow.
Do I need an auto top-off with a sump?
An ATO is strongly recommended. It replaces evaporated water automatically and prevents the sump from running low, which protects the return pump and heater.
How do I prevent a sump overflow during a power outage?
Make sure the sump has enough capacity to hold the water that drains from the display and plumbing when the pump stops. Test this before adding livestock.
Should the heater go in the sump or the display?
Many reef keepers place the heater in the sump, where it is hidden and easy to service. Make sure water flows across it so heat distributes evenly.
How long should I wait before adding corals and fish?
Wait until the system has run leak-free, with stable salinity and temperature, for at least several days. Many keepers wait longer to let the system cycle and biofilm establish.
Conclusion
A well-built aquarium sump set up gives your reef more water, cleaner display glass and room for the equipment that keeps it healthy. Plan the layout, size the sump with a buffer, and test for leaks and outages before adding livestock. For electrical and heater safety, consult a qualified electrician or the equipment manufacturer when in doubt.
Related reading
- Top 8 Aquarium Heater 20 Gallon Picks for Every Setup (2026)
- Floating Thermometer for Aquarium: Which Type Reads Accurately?
Ready to choose one?
