We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

DIY Gravity Auto Top Off: Build a Reef Tank ATO in 8 Steps

Learn how to build a DIY gravity auto top off for your reef tank. Covers reservoir height, tubing, float valves, safety checks and common mistakes.

Updated November 2026

A DIY gravity auto top off uses a reservoir placed above your reef tank and a float valve in the sump to replace evaporated water automatically. In this guide you will learn how to measure head height, pick a reservoir and valve, plumb the system, and test it so it refills only what you lose. Done right, it keeps salinity stable between water changes without a pump running around the clock.

How a Gravity Auto Top Off Works

Gravity ATO systems rely on a simple principle: water flows downhill from a container sitting higher than the sump. When the sump level drops, a float valve opens and lets fresh water siphon or drain in. When the level rises back to the set point, the float closes the valve and the flow stops. Nothing is pumped, so there is no pump to fail, and the system keeps working during a power outage as long as the reservoir has water.

Shopping for one? See our guide: 6 Best Gravity Fed Auto Top Off Systems for Reef Tanks (2026).

The trade-off is that gravity systems depend on height. You need enough vertical distance between the reservoir outlet and the sump’s maximum water line to drive flow at a useful rate. Too little height and the top off will be too slow to keep up with evaporation on a warm day. Too much height and you may overfill the sump if the float fails.

Tools and Supplies You Will Need

  • A food-safe reservoir with a lid, sized for at least one to two weeks of evaporation (commonly 5 to 20 gallons for most reef systems)
  • A float valve rated for saltwater and the tubing size you plan to use
  • Vinyl or PVC tubing, typically 1/4-inch or 3/8-inch inner diameter
  • A check valve or inline shutoff to prevent backflow
  • Silicone or PVC cement for any fittings you permanently join
  • A marker, measuring tape and a level
  • A dedicated RODI or fresh water source, never tap water with untreated chlorine or metals
  • A sump-safe cable or drip loop to keep electrical connections dry

Step 1: Measure Your Head Height

Head height is the vertical distance from the reservoir’s outlet to the highest point of the sump’s water line. Measure with a tape from the bottom of the reservoir outlet fitting up to the water level you want to maintain in the sump. A common target for a reef sump is a head height of 12 to 36 inches. Lower heights give gentle flow and fine control, while higher heights give faster refill.

Mark the sump’s desired maximum water level on the inside of the sump with a dry-erase marker or a strip of tape. This is the point the float should shut off at, so measure from there, not from the top of the sump.

Step 2: Choose the Reservoir Location

Place the reservoir on a sturdy shelf or stand above the sump, ideally close enough that the tubing run stays short. Keep it out of direct sunlight to limit algae growth inside the container. Make sure the shelf can carry the weight of the full reservoir, since a gallon of water weighs about 8.3 pounds.

Step 3: Select the Float Valve

Use a float valve designed for saltwater, with a body and float made of materials that will not corrode. Match the valve’s port size to your tubing. Mount the valve in the sump in a spot where the float can move freely and will not get stuck against the return pump, heater, or skimmer. Many reefers mount the valve inside a small clear container or a PVC standpipe to protect it from turbulence.

Step 4: Install the Check Valve and Shutoff

Place an inline check valve just below the reservoir outlet. This prevents sump water from siphoning back into the reservoir if the tubing is below the sump line, which is a real risk when the system is not properly pressurized. Add a shutoff valve as well so you can isolate the reservoir for cleaning or refilling without draining the tubing.

Step 5: Plumb the Line

Run the tubing from the reservoir to the float valve in as straight a path as possible. Avoid sharp bends, which slow flow and can kink soft tubing. Secure the line with clips so it does not sag below the sump’s maximum water level, because a low dip can create a siphon loop that pulls water out of the sump.

Preventing Unwanted Siphoning

Siphons are the most common cause of sump overflow or sump drain-down in gravity ATO builds. Keep the highest point of the tubing above the sump’s maximum water line where possible, and install an air break or small vent hole near the sump end of the line if your design allows it. Test the system with the reservoir full and the tubing empty to confirm nothing runs when the float is closed.

Step 6: Fill the Reservoir and Prime the Line

Fill the reservoir with fresh water that has been treated and tested. Open the shutoff valve and let the tubing fill. Watch the float closely for the first few hours. It should open and close as the sump level moves, and it should stop the flow at your marked level. If it does not close fully, check the float for debris or a misaligned arm.

Step 7: Test the System

Run a dry test before you connect the system to your live sump. Lower the float by hand to confirm the valve opens, and raise it to confirm the valve closes completely. Then run the system with the sump at its normal level for at least 24 hours. Mark the water line again after the test and confirm it has not climbed above your target.

Step 8: Set a Maintenance Schedule

Clean the reservoir and float valve on a regular schedule, typically every few weeks, to prevent biofilm and mineral buildup. Check the tubing for kinks or leaks, and confirm that the reservoir still has enough water to cover your evaporation rate. Keep a log of how much water the system adds per week so you can spot a sudden change that might signal a leak or a failing valve.

Common Mistakes

  • Using untreated tap water. Chlorine, chloramine, and dissolved metals can harm corals and fish. Use RODI or other treated water.
  • Skipping the check valve. Without it, back-siphoning can drain the sump.
  • Mounting the float in turbulence. Strong flow can make the float bounce and cause inaccurate readings.
  • Setting the target too high. Leave a margin below the overflow line so a failed valve does not flood the stand.
  • Forgetting the reservoir. An empty reservoir turns the system into a sump dry-out risk without warning.
  • Letting the reservoir get dirty. Algae and biofilm can clog the valve and tubing over time.

Tips for a Reliable Build

  • Use a secondary safety float in the sump, wired to shut off the return pump if the water level drops too low.
  • Keep the reservoir lid on to reduce evaporation and contamination.
  • Label your tubing and fittings so future repairs are faster.
  • Compare your build against commercial designs before finalizing your layout, since many reefers use similar configurations.

Several parts make a DIY gravity system easier to build and safer to run. A saltwater-rated float valve is the core component, and a clear reservoir lets you monitor the water level at a glance. Inline check valves help prevent back-siphoning, and a sump safety float adds a second layer of protection against a stuck valve.

  • Float valve for saltwater: A reliable float valve is the heart of any gravity ATO. Look for one with a corrosion-resistant body and a float arm that moves freely. View on Amazon
  • Inline check valve: Prevents water from flowing back into the reservoir and helps stop siphoning when the system is not pressurized. View on Amazon
  • Food-safe reservoir with lid: A dedicated container keeps your top-off water clean and reduces evaporation. View on Amazon
  • Aquarium-grade vinyl tubing: Flexible tubing that resists kinking and works with standard aquarium fittings. View on Amazon

FAQ

How high should the reservoir be above the sump?

Most builds use a head height between 12 and 36 inches. Higher heights refill faster but increase the risk of overfilling if the float fails. Start on the lower end and adjust based on how quickly your system needs water.

Can I use tap water in a gravity ATO?

No. Tap water often contains chlorine, chloramine, and metals that can harm reef inhabitants. Use RODI water or another treated source that has been tested for salinity-compatible purity.

Why does my DIY ATO keep overfilling?

The most common cause is a float that is not closing fully, often because of debris, a misaligned arm, or a valve that is too small for the head height. Check the float travel and clean the valve. A secondary safety float can also help.

Do I need a check valve?

Yes, in most gravity builds. A check valve reduces the risk of back-siphoning from the sump into the reservoir and protects your tank if the tubing runs below the water line at any point.

How often should I clean the reservoir?

Plan to clean it every few weeks, or sooner if you see algae or slime. Regular cleaning keeps the valve and tubing from clogging and helps maintain water quality.

Can a gravity ATO work during a power outage?

Yes, because it does not rely on a pump. As long as the reservoir holds water and the float can move, the system will continue to top off the sump. Still, a power outage is a good time to check your water levels manually.

How do I know how much water to put in the reservoir?

Measure your sump’s evaporation rate over a week or two, then multiply by the number of days you want the reservoir to last. Keep a small margin so the reservoir never runs empty between refills.

Should I consult a professional before building one?

If you are unsure about electrical safety, plumbing layout, or how a secondary safety float should be wired, consult an experienced reef hobbyist or a qualified electrician before proceeding.

Conclusion

A DIY gravity auto top off gives you steady, pump-free water replacement when built with the right head height, a saltwater-rated float valve, and proper backflow protection. Test the system before trusting it, and keep a clean reservoir and a simple maintenance log. With those basics in place, your sump level and salinity will stay far more stable between water changes.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.