We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Skemix Auto Top Off: Setup Steps, Fixes and Gear for Reef Tanks

Learn how a skemix auto top off system works, how to set it up and calibrate it, and how to fix common problems that keep your reef tank stable.

Updated November 2026

A skemix auto top off system keeps your reef tank at a steady water level by adding fresh RO/DI water whenever evaporation drops the level below a set point. Done right, it removes the daily guesswork of topping off by hand and helps keep salinity from drifting. This guide covers what you need, how to set up and calibrate the unit, and the mistakes that most often cause trouble.

What a skemix Auto Top Off Does

An auto top off, often shortened to ATO, uses a float switch or level sensor in your sump or display tank to detect when water has dropped. When the sensor triggers, a small pump or solenoid valve adds top-off water until the level returns to the correct point. Because evaporation removes pure water and leaves salts behind, a reliable ATO matters more than most reefers expect. Manufacturers generally recommend pairing the unit with a dedicated reservoir of RO/DI water rather than tap water.

Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).

Preparing the Reservoir and Plumbing

Before wiring anything, confirm your reservoir water is clean and stable. Store RO/DI water in a sealed container away from direct light to limit algae and bacterial growth, and keep the intake line above the bottom so sediment stays behind.

  1. Mount the reservoir higher than the sump so gravity can help, or confirm the pump you have is rated for the head height.
  2. Run tubing with as few kinks and loops as possible, and secure it so it cannot pull out of the sump or the reservoir.
  3. Place the sensor in a calm area of the sump, away from the return outlet and skimmer intake, so surface turbulence does not cause false triggers.
  4. Plug the pump into a power strip or outlet that you can switch off easily during maintenance.

Calibrating the Sensor and Setting the Level

Calibration decides how the system behaves over days, so take your time with it. Start with the water at your normal operating level, then adjust the sensor so it triggers just below that mark. A common approach is to aim for a shutoff point roughly one-quarter inch above the sensor trigger, so the pump does not run continuously.

  • Fill the sump to your target level and watch it for several minutes to confirm it is stable.
  • Lower the level slowly, or use a marked container to simulate evaporation, and confirm the pump starts at the expected point.
  • Let the pump run until it stops on its own, then measure the final level against your reference mark.
  • Repeat the test once more after the system has run for a day to catch any drift.

Check the Cycle Length

A healthy ATO adds water in short bursts over the day. If the pump runs for long stretches, the sensor may be set too low, the reservoir may be empty, or the intake may be blocked. Log how often the reservoir needs refilling for the first week, since that number tells you how much evaporation to expect.

Common Mistakes to Avoid

  • Using tap water or unfiltered water in the reservoir, which adds dissolved solids and can raise salinity over time.
  • Placing the sensor directly beside the return flow, where waves cause false readings.
  • Skipping a backup plan. A failed sensor can flood or dry out a tank, so consider a secondary shutoff or high-level alarm.
  • Forgetting to clean the sensor and tubing, since salt creep and film can interfere with operation.
  • Assuming the system will keep salinity exact. ATO only replaces water, so test salinity regularly with a refractometer.
  • Digital refractometer: Helps you confirm salinity after the ATO has been running, so you can catch drift early. View on Amazon
  • Replacement float or level sensor: Useful as a spare when troubleshooting, since sensors are the most common failure point. View on Amazon
  • Sealed RO/DI storage container: Keeps top-off water clean and protected from light between refills. View on Amazon

FAQ

Can I use tap water in a skemix auto top off reservoir?

Most reef keepers avoid tap water because it carries dissolved minerals that concentrate as the tank loses water. RO/DI water is the standard choice for top-off.

How often should I check the ATO?

Look at it at least once a day for the first week, then check weekly. Confirm the reservoir level, the sensor position, and that the pump is cycling normally.

What if my ATO keeps running nonstop?

Check the sensor position, look for a blocked intake or an empty reservoir, and confirm the shutoff point is set correctly. Clean the sensor and recalibrate.

Conclusion

A well-calibrated skemix auto top off keeps water level steady and helps protect your salinity between maintenance sessions. Set up clean RO/DI storage, place the sensor carefully, and verify the cycle over several days. Pair the system with regular refractometer checks, and you will catch problems before they reach your corals.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.