We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Auto Top Off Reservoir Ideas: 6 Builds for Reef Tanks (2026)

Explore auto top off reservoir ideas for reef tanks, from simple gravity containers to sump-mounted builds, with setup tips to keep salinity stable.

Updated November 2026

Auto top off reservoir ideas range from a plain storage jug with a float valve to a sealed, sump-integrated container that keeps evaporation losses replaced around the clock. This guide walks through the main designs, the factors that decide which one fits your tank, and the mistakes that cause salinity swings. By the end, you will know which setup suits your tank size and how to size the reservoir correctly.

Choose the Right Reservoir Design

Most reef keepers pick from three basic approaches. Each one solves the same problem, which is replacing evaporated water with fresh RO/DI water, but they differ in how much space they need and how much attention they demand.

Shopping for one? See our guide: 5 Best Auto Top Off Reservoir Options for Reef Tanks (2026).

  • Gravity-fed bucket or container: A sealed container sits above or beside the sump and drains by gravity through a valve controlled by a float or sensor.
  • Pump-fed reservoir: A small pump delivers water from a container placed at floor level, useful when the reservoir must sit below the sump.
  • Integrated sump compartment: A dedicated, isolated chamber in the sump that holds top-off water and feeds the tank through a controller.

Gravity systems are the simplest and cheapest to build. Pump-fed systems tolerate awkward placement. Integrated compartments look clean but take up sump volume you might need for media or equipment.

Size the Reservoir to Your Evaporation Rate

A reservoir should hold enough water to run for at least one to two weeks between refills. Measure your evaporation first by marking the water level with tape and checking it daily for a few days. Many hobbyists see roughly 0.5 to 1 gallon per week on a typical reef tank, though rates swing with room humidity, lighting heat and surface agitation.

Once you have a weekly figure, multiply it by the number of weeks you want between refills and add a 20 percent margin. A 5-gallon container covers most nano and mid-size setups for a week or more, while larger tanks often need 10 gallons or more.

Build a Simple Gravity Reservoir

A basic gravity build works well for most tanks. Follow these steps:

  1. Select a food-safe, opaque container with a tight lid to limit algae growth and evaporation.
  2. Mount the container above the sump at a height that allows steady gravity flow.
  3. Install a float valve or ATO controller on the sump, wired to a solenoid on the reservoir line.
  4. Run tubing from the reservoir outlet to the sump inlet, keeping the line short to reduce head pressure changes.
  5. Test the shutoff by lowering the sump level manually and confirming the valve opens and closes correctly.
  6. Monitor the first week daily, checking that the reservoir level drops at the expected rate.

Consider Sensors and Controllers

Float valves are mechanical and rely on a clean, free-moving arm, so they can stick or fail. Conductivity or optical sensors trigger from water level directly and are less prone to physical blockage. Manufacturers often specify compatibility with particular controllers, so check the sensor type before you buy. If you are unsure how a controller fits your sump, a qualified aquarium technician can review your plumbing before you finalize the layout.

Common Mistakes

  • Using an unsealed container, which invites evaporation, dust and algae growth.
  • Mixing top-off water with salt or leaving salt residue in the reservoir.
  • Placing the reservoir too low, which can cause the sump to back-siphon if plumbing is unvented.
  • Skipping a backup shutoff, so a failed sensor keeps the pump running and floods the sump.
  • Forgetting to flush and clean the reservoir every few months.
  • Food-safe opaque storage container: Blocks light to slow algae growth and keeps the water clean between refills. View on Amazon
  • Aquarium ATO float valve kit: A mechanical shutoff that controls water level in the sump for simple gravity builds. View on Amazon
  • Vinyl aquarium tubing: Carries top-off water from the reservoir to the sump with a flexible, reef-safe line. View on Amazon

FAQ

How big should an auto top off reservoir be?

Measure your daily evaporation, then multiply by the number of days you want between refills plus a margin. Most reef tanks do well with a reservoir that lasts at least one week.

Can I use tap water in an ATO reservoir?

No. Use RO/DI water, since tap water adds dissolved solids that build up as salt creep and raise nutrient levels over time.

Should the reservoir sit above or below the sump?

Above is simplest for gravity feed. Below requires a pump, and any system needs vented plumbing to prevent siphoning. Consult an experienced aquarist if your setup is unusual.

Conclusion

The best auto top off reservoir idea is the one that matches your tank size, evaporation rate and sump layout. Start with a simple sealed container and a reliable shutoff, then add sensors and backups as your system grows. Check your water level daily for the first week, and your reef will stay stable with minimal intervention.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.