We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Avast Marine Works Auto Top-Off: A Step-by-Step Guide for Reef Tanks

Learn how to set up and calibrate an avast marine works auto top-off for your reef tank, with steps, common mistakes and fixes for stable salinity.

Updated November 2026

An avast marine works auto top-off, often shortened to ATO, keeps your reef tank’s water level steady by adding fresh RO/DI water as evaporation lowers it. This guide walks you through placement, plumbing, sensor setup and calibration so the system tops off reliably without overfilling or running dry. Done right, your salinity stays stable between water changes.

Before You Install an Auto Top-Off

Start by confirming your reservoir and sump layout can accommodate the system. Most ATO setups draw from a dedicated container of RO/DI water placed above or beside the sump. Check that the reservoir sits high enough for gravity feed if your model uses one, and that the sensor location is easy to reach for cleaning.

Shopping for one? See our guide: 5 Best Innovative Marine Auto Top Off Systems for Reef Tanks (2026).

  • A reservoir sized for at least several days of evaporation
  • Tubing rated for saltwater use, and a spare length for adjustments
  • An outlet or power strip with surge protection
  • A marked log or notebook for tracking top-off volumes

Installing the Sensor and Pump

Mount the float or probe in the sump’s return chamber, away from the skimmer intake and the return pump’s turbulence. Turbulent water causes false readings, and the sensor should respond only to the true water level. Route the pump tubing so it discharges into a sump chamber that mixes well, rather than directly onto the surface where it can form a stagnant pocket.

Calibrating the Water Level

Calibration sets the level at which the system starts and stops adding water. Follow these steps:

  1. Let the system run until the sump reaches its normal operating level, then mark the waterline.
  2. Adjust the sensor height so the pump shuts off at that mark, leaving a small margin below your overflow.
  3. Run a dry test: unplug or lift the sensor to confirm the pump starts, then re-seat it and confirm it stops.
  4. Watch the first full cycle to check that the water rise is gradual and never reaches the overflow line.

Most manufacturers specify a safety margin between the shutoff point and the overflow. Keep that margin, even if your tank seems to tolerate a higher level.

Monitoring and Maintaining the System

An ATO is not truly set-and-forget. Check the reservoir level weekly, clean the sensor to remove salt creep and algae, and inspect tubing for kinks or micro-leaks. Keep the RO/DI reservoir covered to limit contamination. If you notice the top-off volume suddenly jumping, investigate before assuming the system is working correctly, since a jump often points to a leak or an evaporation change from a new heater or lid adjustment.

Common Mistakes and Tips

  • Topping off with tap water or unfiltered water, which raises nitrate, phosphate and salinity problems.
  • Placing the sensor in a high-flow area, causing erratic starts and stops.
  • Skipping the dry test after changing the sensor height.
  • Forgetting that salt creeps up the sensor and interferes with readings.
  • Relying on the ATO without a backup check, such as a weekly refractometer reading.

For more detailed setup routines, see Avast Auto Top Off: A Step-by-Step Guide for Reef Tanks and Marine Auto Top Off: How to Set Up and Calibrate an ATO for Reef Tanks.

  • Tunze Osmolator 3155 Universal: A widely used controller that many reefers pair with an ATO reservoir for consistent level control. View on Amazon
  • Neptune Systems Apex Controller: Lets you monitor top-off events and alert you when the reservoir runs low. View on Amazon
  • Marine saltwater-rated tubing: Resists salt creep and degradation better than standard vinyl. View on Amazon

For comparisons of ATO systems across brands, read 7 Best Auto Top Off Marine Tank Systems for Reef Tanks (2026).

FAQ

How often should I refill the ATO reservoir?

Refill it whenever the level drops to about a quarter of its capacity, and check it at least once a week. Evaporation rates vary with lid use, room humidity and heater output.

Can an ATO replace regular water changes?

No. An ATO only replaces evaporated water. Water changes remove dissolved waste and replenish trace elements, so both are needed.

What should I do if the ATO overfills?

Turn off the pump, siphon out the excess, and recheck the sensor height and placement. If the problem continues, consult the manufacturer or an experienced reef retailer for help.

Conclusion

A properly installed avast marine works auto top-off keeps your water level and salinity steady with minimal daily effort. Take time to place the sensor well, calibrate with a safety margin, and check the system weekly. A few minutes of attention now prevents the bigger problems that come from a dry or overfilled sump.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.