Apex Auto Top Off: Setup, Calibration and Fixes for Reef Tanks
Learn how an Apex auto top off works, how to set it up and calibrate the float sensor, and how to fix common reef tank problems. Step-by-step.
Updated November 2026
An apex auto top off is a controller-driven system that keeps your reef tank at a steady water level by adding fresh water (usually RODI water) whenever evaporation drops the level below a set point. In this guide you will learn how the system works, how to wire and mount the sensor, how to calibrate the top off so it stops at the right height, and how to troubleshoot the problems reefers run into most often. The goal is a stable tank that never runs dry and never floods your sump.
How an Apex Auto Top Off Works
Evaporation removes pure water and leaves salt behind, so the tank’s salinity creeps upward between water changes. An auto top off solves the level part of that problem. A float or probe sensor sits in your sump or display, a pump draws from a reservoir of fresh water, and the controller decides when to run that pump. Apex controllers, including the Neptune Apex line, read the sensor state and switch a power outlet or relay accordingly.
Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).
There are two common sensing approaches. A float switch uses a buoyant arm that closes a contact at a fixed height. A conductivity probe measures whether water is touching its electrodes. Both work, but each needs a correct setup. Many owners report that the float style is more forgiving to install, while probes respond faster to small level changes.
What You Need Before You Start
Gather everything before you touch the tank. A clean, planned installation prevents most of the problems described later in this article.
- An Apex controller or compatible outlet module with at least one dedicated outlet for the top off pump
- A top off sensor (float or probe) rated for saltwater
- A submersible or inline pump sized for your reservoir height and flow needs
- RODI water in a sealed reservoir, with a lid to limit contamination
- Silicone-free tubing of the correct inner diameter, plus a check valve
- Suction cup mounts or a bracket for the sensor
- A marker, a ruler and a small level for marking the target water line
- A refractometer or calibrated hydrometer to verify salinity after changes
Use dedicated tubing for RODI water only. Garden hose or tap-connected lines can introduce contaminants that show up later as nuisance algae or cloudy water.
Step-by-Step Installation
Step 1: Choose the Sensor Location
Place the sensor in the sump, not in the display, if you have one. The sump is usually more stable and less affected by surface agitation. Mount the sensor in a spot where splashing or bubbles from the skimmer will not trigger false readings. For a float, make sure the arm can move freely through its full travel without touching the sump wall.
Step 2: Set the Target Water Line
Mark the ideal water level on the sump with a removable marker. Aim for the level where the sump is full enough to keep the return pump primed but leaves headroom so a small overshoot will not spill. Many reefers leave about one inch of clearance below the sump rim. Set the sensor so it activates at the lower bound of your normal operating range, typically a quarter inch below your mark.
Step 3: Plumb the Pump and Reservoir
- Place the RODI reservoir higher than the sump outlet point where the top off tubing enters, or use a pump rated for the head height.
- Connect the pump outlet to the tubing and run it to the sump, ending with a drip loop or an upturned end above the water line to prevent siphoning.
- Install a check valve on the pump outlet line to stop back flow when the pump is off.
- Secure all tubing so it cannot kink or come loose inside the cabinet.
Step 4: Wire the Controller
Plug the top off pump into the dedicated outlet on your controller. Connect the sensor to its input port. Confirm the controller recognizes the sensor state before you rely on it. Keep the controller and any power strips above the potential splash zone and use drip loops on all cords.
Calibrating the Apex Top Off
Calibration is where most setups succeed or fail. The goal is to make the pump stop at the correct level, not to fill to the brim or run dry.
Set the Trigger Behavior
Program the controller so the pump runs only while the sensor reports low water, with a maximum run time as a safety limit. A maximum run time protects you if the sensor fails in the open state. Choose a value that comfortably covers a normal refill but stops the pump before a large overflow. Many owners start with a conservative limit and extend it only after observing actual refill times.
Verify the Level by Observation
Run the pump manually and watch the sump. Stop it at your target line and note how far the water rises after the pump stops, since residual water in tubing can keep draining. Adjust the sensor height until the pump shuts off at the correct point. Recheck after the system has run for a full day.
Check Salinity After Calibration
An auto top off adds only fresh water, so salinity rises between changes if your reservoir is not properly mixed. Test your display regularly with a refractometer. If salinity drifts upward faster than expected, check the reservoir water quality and the sensor position, which may be triggering frequent top offs.
Troubleshooting Common Problems
| Symptom | Likely cause | Fix |
|---|---|---|
| Pump runs constantly | Sensor stuck low or fouled | Clean the sensor, check its travel, confirm wiring |
| Tank overflows | Sensor set too high or maximum run time too long | Lower the sensor, shorten the run limit, verify the shutoff |
| Pump does not start | Sensor not triggering, outlet not programmed, pump clogged | Test the sensor manually, check the outlet assignment, clear the intake |
| Salinity rising | Water in the reservoir not mixed or topped off too often | Mix reservoir to correct salinity, review sensor placement |
| Air in the line | Reservoir level low or loose fitting | Refill reservoir, tighten fittings, prime the pump |
Tips and Common Mistakes
Mistakes to Avoid
- Using tap water or unfiltered water in the reservoir. This is the most common cause of nuisance algae and cloudy water.
- Skipping the check valve. Without it, the tank can siphon back into the reservoir when the pump stops.
- Setting the sensor too high. This leaves no safety margin and often leads to overflow after a power interruption.
- Ignoring the reservoir. An empty reservoir is a silent failure that only shows up when the sump runs low.
- Relying on the sensor alone. Always pair it with a maximum run time and a periodic visual check.
Helpful Tips
- Test the failsafe by unplugging the sensor or manually holding it low, then confirming the pump stops at your time limit.
- Clean the sensor monthly to prevent salt creep and algae from changing its response.
- Keep a logbook of refill times and salinity readings. Sudden changes often reveal sensor or evaporation problems early.
- Use a reservoir lid and keep it closed to reduce contamination and evaporation loss.
- If you run a protein skimmer, check that its height does not interfere with the sensor float.
Recommended gear
Gear is the easiest way to make this system reliable, but choose parts that match your controller and tank size.
- Apex-compatible outlet module for running the top off pump from your controller, since a dedicated outlet makes programming and failsafes simpler. View on Amazon
- Saltwater-rated float sensor to trigger the pump at a fixed level with a simple, easy-to-check mechanism. View on Amazon
- Submersible top off pump sized for your reservoir height so refills run at a steady rate. View on Amazon
- Inline check valve to prevent backflow and siphoning when the pump stops. View on Amazon
FAQ
Does an apex auto top off need a dedicated outlet?
Dedicated is strongly recommended. It lets you assign a maximum run time and failsafe behavior specifically to the top off pump without affecting other equipment.
Can I use tap water in the reservoir?
No. Use RODI water. Tap water carries dissolved solids and contaminants that can cause algae, cloudiness and salinity drift.
How often should I clean the sensor?
Many reefers clean the sensor monthly, or sooner if salt creep or algae is visible. Fouling can change its response and cause missed or false triggers.
Why does my tank overflow after a power outage?
Some setups restart with the pump in an unexpected state, or the sensor reads incorrectly while the system is recovering. Keeping a safe sensor height and a maximum run time limits the damage.
Should the sensor go in the display or the sump?
The sump is usually preferred because it is more stable and less affected by surface movement and splashing.
How do I know if salinity is rising?
Test the display with a refractometer on a regular schedule. A steady upward trend between water changes suggests the top off is adding too little salt-free water or that the reservoir is not correct.
Is an apex auto top off safe for corals?
The system itself does not harm corals when properly calibrated and fed with RODI water. Sudden level swings from misconfiguration can stress livestock, so verify your setup carefully. For electrical safety questions, consult a licensed electrician.
Can the top off be added to an existing sump?
Yes. Most setups can be retrofitted with a sensor, pump and reservoir. Plan the sensor height and tubing route before drilling or modifying anything.
Conclusion
An apex auto top off keeps your reef tank stable by replacing evaporated water automatically, as long as the sensor, pump and reservoir are set up correctly. Calibrate carefully, add a maximum run time, and use only RODI water. Check the system regularly and keep a log of refill behavior so problems show up early. With these steps, your Apex top off will protect your tank without becoming a source of new issues.
Related reading
- Tunze Osmolator 3 Auto Top Off: Setup and Calibration Guide
- Tunze Auto Top Off: Setup, Calibration and Troubleshooting Guide (2026)
- Tunze 3155.000 Osmolator Auto Top Off System: Setup, Calibration and Fixes
- Top 7 Auto Top Offs for Nano Tank Systems with Reliable Sensing
- Top 3 Neptune Auto Top Off Systems Compared for Reef Tanks
- Osmolator 3 Auto Top Off: Setup, Calibration and Fixes for Reef Tanks
Ready to choose one?
