BRS Auto Top Off: Setup, Calibration and Common Fixes for Reef Tanks
Learn how a BRS auto top off works, how to set it up and calibrate it, and how to fix common problems so your reef tank's salinity stays stable.
Updated November 2026
A brs auto top off is a small pump and sensor system that replaces the water your reef tank loses to evaporation, keeping the water level steady without manual refilling. By the end of this guide, you will know how to plan the reservoir and mounting, wire and calibrate the sensor, test the system safely, and troubleshoot the problems reefers run into most often. The goal is simple: a stable water level that keeps salinity and coral chemistry from drifting between your regular maintenance sessions.
What a BRS Auto Top Off Does and Why It Matters
Evaporation removes pure water from the tank, not salt. Each day, the water that leaves the system is fresh water, so the remaining water gets saltier. A top-off system adds back fresh water (usually reverse osmosis/deionized water) as needed. Because the fill is triggered by a level sensor, the tank rarely drops far enough to expose equipment, and salinity stays closer to target than it would with occasional hand top-offs.
Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).
Most auto top off designs share the same core parts: a reservoir of RO/DI water, a small submersible or inline pump, a float switch or electronic probe in the display or sump, and a controller or relay that switches the pump on and off. Understanding those parts makes setup and troubleshooting much easier.
Before You Start: Planning Your Setup
Good results start with planning. Take a few minutes to confirm the following before you drill, wire, or plug anything in.
- Water source: Use RO/DI water only. Tap water can carry phosphate, silicate, and dissolved solids that feed nuisance algae and raise your tank’s total dissolved solids.
- Reservoir: Choose a container with a lid, sized for at least several days of evaporation. Keep it close to the tank so tubing runs stay short.
- Sensor location: The sensor must sit in the sump or display where the water level changes in a stable way, away from heavy turbulence and return flow.
- Power: Plug the pump and controller into a surge-protected outlet, ideally on a circuit that is not shared with heaters or large powerheads.
- Tubing: Confirm the tubing ID matches the pump outlet and the fittings you intend to use.
Tools and supplies you will need
- Fresh RO/DI water in a clean, covered reservoir
- Aquarium-safe tubing and clamps or check valves
- A marker or tape to note the sensor position
- A refractometer or calibrated salinity tester
- A clean towel and a small cup for measuring test volumes
- A surge protector with a switched outlet, if available
Step-by-Step Installation
Step 1: Mount the reservoir and pump
Place the reservoir at or slightly above the tank’s water line so gravity does not siphon water back into the reservoir when the pump is off. If the reservoir sits lower than the tank, install a check valve on the fill line. Keep the pump submerged in the reservoir, or mount it per the manufacturer’s instructions, and make sure the intake is not sucking up any sediment from the bottom.
Step 2: Route the tubing
Run the tubing with gentle curves and no sharp kinks. Kinks restrict flow and can cause the pump to run hot or fail prematurely. Secure the line so it cannot slip out of the tank or sump, and place the outlet where the water will mix into the sump rather than splashing directly onto a protein skimmer intake.
Step 3: Position the sensor
Set the sensor so it reads the water level that matches your target. Many reefers place the sensor in the sump, at the point where the water level is roughly 1/8 to 1/4 inch above the lowest acceptable level. Test by filling or draining a small amount and watching whether the sensor responds cleanly. Avoid placing the sensor where a return pump outlet or drain creates surface waves.
Step 4: Wire the controller
Connect the sensor leads to the controller, then connect the pump to the relay output. Double-check that all low-voltage and mains connections are sealed and kept away from water. Never run wiring that could contact saltwater, and use drip loops so water cannot track down the cable into the outlet.
Calibrating the Sensor
Calibration sets the level at which the pump starts and stops. Follow your model’s manual for button sequences, but the general logic is the same across most systems.
- Let the tank settle for at least 30 minutes so the water level is stable.
- Enter calibration mode on the controller and set the “full” or upper point at the exact level you want to maintain.
- Lower the water level slightly, either by pausing the return pump or by letting the tank drop naturally, and set the “low” or activation point.
- Let the pump run once. Watch for two things: it should stop when the sensor reaches the full mark, and the level should not overshoot.
- Check that the reservoir has enough water and that the pump is primed. Dry running can damage the impeller.
Setting the safety limit
Many systems include a maximum run time or a fault alarm. Enable it. If the sensor fails or the reservoir runs empty, a timeout stops the pump before the sump overflows. Some reefers add a separate float switch in the sump as a backup, which is a common and sensible precaution.
Testing the System
Once calibrated, run the system through at least one full fill cycle while you watch it. Confirm that:
- The pump starts when the level drops to the activation point
- It stops at the full point without splashing or overflowing
- The water mixes evenly with the sump rather than pooling on one side
- No air is trapped in the line, which can cause pump cavitation
Measure salinity before and after a few days of operation. Keep in mind that the top-off water is fresh, so salinity should drift slightly upward between fills, which is normal. Consistent behavior over several days is what tells you the system is working.
Common Problems and Fixes
| Symptom | Likely cause | What to do |
|---|---|---|
| Pump runs but no water reaches the tank | Air in the line or clogged intake | Prime the pump, clear the intake, check for kinks |
| Tank overflows | Sensor set too high or stuck | Recalibrate, clean the sensor, enable backup float switch |
| Pump short-cycles | Sensor placed in turbulent water | Move the sensor to a calmer spot |
| Pump runs constantly | Sensor not detecting the water level | Check wiring, clean the probe, confirm calibration |
| Pump buzzes or loses power | Dry running or a worn impeller | Refill the reservoir, check the pump, replace if worn |
For a more detailed symptom-by-symptom walkthrough, see Tunze Auto Top Off: Setup, Calibration and Troubleshooting Guide (2026) and Magtool Auto Top Off: Setup, Calibration and Troubleshooting for Reef Tanks, which cover similar sensing designs and common fault patterns.
Common Mistakes
- Using tap water in the reservoir. This is the most common cause of algae and TDS problems.
- Leaving the reservoir open. Dust, debris, and bacteria can enter and contaminate your fill water.
- Placing the sensor where splash or flow creates false readings.
- Skipping the backup float switch or overflow safety. A single failure should never flood the room.
- Forgetting to check the reservoir level. An empty reservoir means the tank will slowly drop and salinity will climb.
- Setting the full point too high, which causes overflow when the return pump surges.
Tips for Reliable Operation
- Clean the sensor and pump intake monthly, or whenever you notice film or algae.
- Keep a log of reservoir refills so you can spot a sudden increase in top-off volume, which may signal a leak or evaporation spike.
- Check the system after any lid change, heater adjustment, or room temperature change, since evaporation rates shift with them.
- Test your salinity with a refractometer rather than relying on a single measurement.
- Run a short test after maintenance to confirm the pump and sensor still behave correctly.
Recommended gear
- Tunze Osmolator 3155 Auto Top Off: A widely used controller-and-pump design with a dedicated sensing probe, useful for reefers who want a standalone system with a clear calibration routine.
View on Amazon - Neptune Systems Apex ATO Kit: A kit that pairs top-off control with a larger controller platform, helpful for tanks that already use a centralized monitoring system.
View on Amazon - Reef Octopus RO/DI Reservoir: A dedicated RO/DI storage container that keeps fill water clean and covered until it is used.
View on Amazon - Hanna Instruments HI98319 Refractometer: A handheld salinity meter for checking your tank after installation and during the first weeks of operation.
View on Amazon
FAQ
What water should I use in a BRS auto top off reservoir?
Use RO/DI water only. Fresh tap water can introduce phosphate, silicate, and dissolved solids that encourage algae and raise your tank’s TDS over time.
How often should I refill the top-off reservoir?
It depends on reservoir size and evaporation rate. Check it at least weekly, and more often in warm rooms or with large, open-top tanks. Many reefers keep a few days of reserve water on hand.
Why is my auto top off adding too much water?
The most common causes are a sensor placed in turbulent water, a full-level setting that is too high, or a stuck sensor. Recalibrate, relocate the sensor, and clean it.
Can I use an auto top off without a backup float switch?
You can, but a backup float switch or maximum run-time limit is strongly recommended. It prevents a single sensor failure from flooding the room.
Does an auto top off change my salinity?
It helps keep salinity stable by replacing only the fresh water that evaporates. Salinity still drifts slightly between fills because the added water is fresh, so test periodically with a refractometer.
Why does my pump keep running even after the tank is full?
The sensor may be dirty, misaligned, or not detecting the water surface. Clean it, check its position, and confirm the calibration points.
Is a BRS auto top off safe to leave running unattended?
With a properly calibrated sensor, a backup float switch, and a run-time limit, it can run unattended for long stretches. Still, check the reservoir and system regularly. If you are unsure about electrical safety, consult a qualified electrician.
Conclusion
A brs auto top off keeps your reef tank’s water level and salinity steady by replacing only the fresh water that evaporates. Plan your reservoir, sensor position, and power supply before installation, calibrate carefully, and test through a full fill cycle. With a backup safety layer and regular maintenance, the system will do its job quietly for months.
Related reading
- Tunze Osmolator 3 Nano Auto Top Off: Setup and Calibration in 7 Steps
- Tunze Osmolator 3 Auto Top Off: Setup and Calibration Guide
Ready to choose one?
