Auto Top Off Poker: Meaning, Setup and Safety for Reef Tanks
Auto top off poker is the float-switch sensor that tops off evaporated water in your reef tank. Learn how it works, how to set and test it, and avoid common fai
Updated November 2026
An auto top off poker is the float-switch or sensor probe that tells your auto top off system when the water in your sump or display tank has dropped below a set level. Once you understand how it works, you can position it correctly, calibrate it, and check it regularly so that evaporated freshwater gets replaced automatically without risking a dry pump or a salt creep disaster. This guide walks through the parts, the setup, the testing routine, and the fixes for the most common problems.
What an Auto Top Off Poker Actually Does
In most reef setups, the auto top off poker is a sensor stick that sits inside a reservoir or sump. It is usually a float switch, a conductivity probe, or an optical sensor housed in a rigid tube. When the water level drops past the sensor, the controller or relay closes a circuit and starts the top off pump. When the water rises back to the set height, the sensor opens the circuit and the pump stops.
Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).
Evaporation removes pure water and leaves salt behind, so the water level falls while salinity rises. A reliable auto top off poker keeps that level within a narrow band, usually a few millimeters, which protects your pump from running dry and keeps salinity stable. Many reefers pair the sensor with a fresh water reservoir fitted with a float valve as a second line of defense.
Parts You Will Need
Before you start, gather everything so you are not stopping halfway through the install. Most setups need:
- The auto top off poker or sensor probe, with its cable and mounting bracket
- A controller, relay box, or ATO unit that accepts the sensor input
- A top off pump rated for your flow requirement, plus tubing sized to the pump outlet
- A fresh water reservoir with a float valve or a sealed container
- Zip ties, a drill or mounting hardware, and a small level or ruler
- Tape or marker for labeling the high and low water marks
Step-by-Step Setup
Step 1: Choose the Sensor Location
Mount the auto top off poker in a spot where water movement is gentle. Placing it directly beside a return outlet or a skimmer intake can cause false readings from surface turbulence. A sump compartment with a calm surface is ideal. Keep the sensor away from the protein skimmer’s airline and from any spot where salt creep or bubbles collect.
Step 2: Set the Working Height
Decide on two marks: a high-water mark where the pump should stop, and a low-water mark where the pump should start. Many hobbyists set the working band at about 5 to 10 mm between the two marks. Make sure the low-water point still sits above the pump intake so the pump never pulls air.
Step 3: Mount Securely
Fix the probe so it cannot drift, vibrate, or tilt. A loose poker that shifts with pump vibration will cause erratic cycling. Use the bracket and zip ties, then confirm the probe is vertical and fully submerged at the top-off point.
Step 4: Wire to the Controller
Connect the sensor cable to the controller input, then plug the top off pump into the controlled outlet. Keep high-voltage and low-voltage wiring separated. Use a drip loop so water cannot run down the cable into the outlet.
Step 5: Calibrate the Sensor
Calibration matters more than people expect. Follow the manufacturer’s procedure for your model. Generally, you fill the sump to the desired high mark, run the calibration function, then allow the water to drop to the low mark to confirm the pump switches on at the right point. Many controllers store these two points automatically.
Testing and Routine Checks
Once installed, run a full cycle test before trusting the system overnight. Manually drain a small amount of water and watch whether the pump starts at the low mark and stops at the high mark. Repeat the test once a week, and check for salt buildup on the probe. Salt crusts can insulate the sensor and cause late or missed triggers.
| Check | Frequency | What to Look For |
|---|---|---|
| Visual water level | Daily | Level inside the working band |
| Probe cleaning | Weekly | Salt film or algae on the sensor |
| Pump cycle test | Weekly | Pump starts and stops at the correct marks |
| Fresh water reservoir | Weekly | Adequate volume and float valve working |
| Full calibration | After any move or repair | Setpoints match the tank |
For model-specific steps, many owners work from guides such as Tunze Auto Top Off: Setup, Calibration and Troubleshooting Guide (2026), which cover the exact calibration sequence for that brand. If you run a nano system, Osmolator 3 Nano Auto Top Off: 5 Best Systems for Reef Tanks (2026) compares compact options with different sensing styles.
Common Mistakes
- Mounting the probe in turbulent water, which causes false triggers
- Setting the low-water mark too close to the pump intake, risking a dry run
- Skipping calibration after moving the sump or changing the water level
- Letting salt crust build up on the sensor until it stops responding
- Filling the fresh water reservoir with tap water rather than RO/DI water, which adds contaminants to the tank
- Relying on a single sensor with no visual check or backup float valve
Troubleshooting Tips
If the pump runs continuously, the probe may be stuck in the on position, a wire may be shorted, or the controller may be set to the wrong mode. If the pump never starts, check power, confirm the sensor is submerged at the low mark, and test continuity on the probe. Frequent cycling with tiny water changes often points to a loose mount or surface ripple. When troubleshooting, change one variable at a time so you know which fix worked. If you suspect an electrical fault, unplug the system and consult a qualified electrician or your equipment manufacturer before continuing.
Recommended gear
- Replacement top off pump: A spare pump matched to your sensor voltage lets you recover quickly if one fails. View on Amazon
- Spare auto top off probe: Keeping a second sensor on hand prevents a long shutdown if the probe is damaged. View on Amazon
- RO/DI top off water container: A sealed reservoir keeps topping water clean and protects against contamination. View on Amazon
FAQ
What is an auto top off poker?
It is the sensor probe, often a float switch or conductivity sensor, that detects the water level in your sump or display tank and signals the top off pump when water needs replacing.
Where should I mount the auto top off poker?
Mount it in calm water away from the skimmer intake, return flow, and bubbles. The probe should sit firmly at the low-water point and stay vertical.
How often should I clean the sensor?
Most reefers inspect and wipe the probe weekly. Salt creep and algae can interfere with readings, so heavier buildup may need more frequent cleaning.
Can I use tap water in my top off reservoir?
Use RO/DI water. Tap water can carry minerals, chlorine residue, and other contaminants that build up in a reef tank over time.
Why does my auto top off keep running?
Common causes include a stuck or fouled probe, a shorted wire, a misset controller, or a leaking reservoir that never reaches the low mark. Check each in turn.
Do I need calibration after moving my sump?
Yes. Changing the physical water level or probe position alters the setpoints, so recalibrate to match the new tank height.
Is a float valve enough without a sensor?
A float valve on a fresh water reservoir controls the reservoir, not the tank level, so it does not replace a sensor in the display or sump. It works best as a backup.
When should I call a professional?
If you see scorched wiring, a tripped breaker, or water near electrical connections, unplug the system and consult a licensed electrician or the manufacturer before continuing.
Conclusion
An auto top off poker is a small component with a big job: keeping your reef’s water level and salinity stable without constant attention. Position it carefully, calibrate it to your exact tank, and check it on a weekly schedule. Pair it with a clean RO/DI reservoir and a backup plan, and your tank will stay steady through the long nights and busy weeks alike.
Related reading
- Tunze Osmolator 3 Nano Auto Top Off: Setup and Calibration in 7 Steps
- Tunze Osmolator 3 Auto Top Off: Setup and Calibration Guide
- Tunze 3155.000 Osmolator Auto Top Off System: Setup, Calibration and Fixes
- Top 7 Pool Auto Top Off Systems for Reef Tanks Compared (2026)
Ready to choose one?
