We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Auto Top Off Unit for Reef Tanks: 7 Steps to Set It Up Right

Learn how an auto top off unit keeps your reef tank salinity stable. Choose the right type, set up the sensor, calibrate it, and avoid common mistakes.

Updated November 2026

An auto top off unit, usually shortened to ATO, is a device that replaces water lost to evaporation so your reef tank’s water level and salinity stay steady. In this guide you will learn how an auto top off unit works, how to choose the right type for your system, how to install and calibrate it, and how to troubleshoot the problems reefers run into most often. Follow the steps below and you should end up with a system that tops off reliably without overflowing or running your pump dry.

How an Auto Top Off Unit Works

Evaporation removes pure water from the tank and leaves the salt behind, so salinity climbs over time. An auto top off unit corrects this by adding fresh water, usually reverse osmosis/deionized (RO/DI) water, in small amounts whenever the water level drops below a set point. Because the water being added is free of salt, the tank’s specific gravity stays closer to its target, which matters for corals, invertebrates and fish that are sensitive to swings.

Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).

Most systems share the same basic parts:

  • A reservoir holding RO/DI water, typically a food-safe container placed above or beside the sump.
  • A pump or gravity line that moves water from the reservoir to the sump or display.
  • A level sensor that detects when the water falls to the set point.
  • A controller (or a float valve in simpler designs) that switches the pump or valve on and off.

Choosing the Right Type of Auto Top Off Unit

Before buying or building anything, match the system to your tank size, sump layout and how much you want to automate. Your main options are:

  • Float-switch systems. A float rises and falls with the water level and triggers a pump or valve. These are simple and widely used, but the float can stick or foul over time.
  • Conductivity or electrode systems. Probes detect water contact at set heights. They have no moving parts to jam, though the probes need periodic cleaning to avoid false readings from salt creep.
  • Ultrasonic or optical systems. These measure level without touching the water. They are less common and usually more expensive, but they avoid contact fouling entirely.
  • Gravity-fed systems. A reservoir sits above the sump and a float or solenoid valve controls flow with no pump. They run quietly and are a common choice for DIY builds, though they need enough height difference to work.

Consider three practical factors as well. Make sure the unit handles your sump’s volume and evaporation rate, choose a reservoir large enough for at least several days of top-off water, and plan for a backup shutoff so a stuck sensor cannot flood the room.

Tools and Supplies You Will Need

Gather these items before you start installation:

  1. The auto top off unit with its sensor, pump or valve, and power supply
  2. A reservoir made from food-safe plastic with a lid
  3. RO/DI water, tested with a TDS meter (target 0 ppm, or as close as your filter allows)
  4. Vinyl or silicone tubing sized to the pump or valve fittings
  5. A GFCI outlet or power strip for the controller and pump
  6. A refractometer or calibrated hydrometer for checking salinity
  7. Zip ties, a small level, and a soft cloth for cleaning sensors

Step-by-Step Installation and Setup

Step 1: Position the Reservoir and Sensor

Place the reservoir where it sits above the sump’s maximum water line so gravity helps if your pump fails. Mount the sensor in a calm area of the sump, away from the return outlet and skimmer intake, where waves and bubbles will not trigger false readings. Keep the sensor away from the protein skimmer’s foam zone.

Step 2: Mount the Pump or Valve

Secure the pump or valve so the outlet tubing runs cleanly to the sump. Keep tubing loops high enough to prevent siphoning when the pump is off. If the system uses a float valve on the reservoir, confirm that it closes fully at the top of its travel.

Step 3: Connect Power Safely

Plug the controller and pump into a GFCI-protected outlet. Keep all power connections above the water line and away from splashes. Never run cords through the sump’s water.

Step 4: Fill the Reservoir with RO/DI Water

Fill the reservoir with RO/DI water and check it with a TDS meter before adding it to the tank. Using tap water or unfiltered water is one of the fastest ways to raise salinity and introduce nutrients or contaminants.

Step 5: Set the Level Points

Mark the sump’s normal water line with tape. Adjust the sensor so the pump engages about 1/4 inch below that mark and shuts off no higher than the mark plus a small margin. Leave a safety buffer between the top-off height and the sump’s overflow point so a fault cannot cause spillage.

Step 6: Calibrate and Test

Follow the manufacturer’s calibration routine, which usually involves holding the sensor at the low and high points and saving each reading. Then test the system by manually lowering the water level slightly or raising the sensor to confirm the pump starts and stops at the right times. Let it run for 24 hours and watch the levels.

Auto Top Off Setup Checklist

Check What to Confirm
Sensor placement Calm water, away from skimmer and return
Reservoir Above sump max line, lid on, food-safe
Water source RO/DI, TDS near 0 ppm
Level settings Pump start and stop points set with safety buffer
Power GFCI outlet, no cords in water
Test run 24 hours of stable operation

Common Mistakes to Avoid

  • Using tap water or untested RO/DI water. Dissolved solids and nutrients build up over time and can fuel algae.
  • Setting the top-off point too close to the overflow. Leave margin so a sensor fault does not spill water onto your floor.
  • Letting sensors foul. Salt creep and algae coat probes and floats. Clean them weekly.
  • Forgetting the reservoir. An empty reservoir means the tank stops topping off silently. Check levels as part of your routine maintenance.
  • Skipping a backup. Consider a secondary shutoff or leak sensor, especially for systems that run unattended.

Troubleshooting Tips

If the unit runs constantly, check for a sensor obstructed by debris or salt, a leaking valve, or a water level that is actually dropping faster than expected. If it never turns on, confirm power, check that the sensor is making contact, and make sure the reservoir has water. Always verify the actual level with a marked line rather than trusting the controller alone.

  • Tunze Osmolator 3155 Auto Top Off: A widely used controller-based system from a major reef equipment maker, appreciated by owners for its electrode-style sensing and adjustable settings. View on Amazon
  • Neptune Systems Apex Top Off Kit: A controller-integrated kit that pairs with a larger automation ecosystem, useful if you already run an Apex-style controller. View on Amazon
  • TDS meter: Verifies your RO/DI water is near 0 ppm before it goes into the reservoir. View on Amazon
  • Digital refractometer: Lets you confirm salinity is staying on target after the unit starts running. View on Amazon

Further Reading

For model-specific setup, see Tunze Osmolator 3 Auto Top Off: Setup and Calibration Guide or Neptune Auto Top Off Kit: Setup, Calibration and Common Fixes. If you prefer a DIY approach, DIY Gravity Auto Top Off: Build a Reef Tank ATO in 8 Steps walks through a build from scratch. If your unit is misbehaving, JBJ Auto Top Off Not Working: Troubleshooting Steps That Fix It covers common fixes.

FAQ

Can I use tap water in an auto top off unit?

No. Tap water contains dissolved minerals, chlorine and nutrients that accumulate in a reef tank. Use RO/DI water and confirm it reads near 0 ppm on a TDS meter.

How often should I clean the sensor?

Check it weekly. Salt creep and algae can cause false readings, so wipe probes or floats with a soft cloth and clean them as needed.

Why does my auto top off unit run constantly?

The most common causes are a dirty or obstructed sensor, a leaking valve or line, or a real evaporation problem caused by heat or a sump that is too small for the tank.

Do I still need to check salinity if I use an auto top off unit?

Yes. An auto top off unit adds fresh water, so salinity should be verified regularly with a refractometer or calibrated hydrometer, especially after the system is first installed.

Should the reservoir be above or below the sump?

Above is generally preferred because gravity can help if the pump fails, and it allows gravity-fed designs to work without extra equipment. For another angle, check out Nano Reef Tank Set Up: A Step-by-Step Guide for Beginners.

How much RO/DI water should the reservoir hold?

Size it for several days of evaporation at your tank’s typical rate. A larger reservoir means fewer refills and more time to notice problems.

What is a safe distance between the top-off point and the overflow?

Leave a visible margin, often around an inch or more depending on the sump, so a sensor fault cannot push water over the overflow. Confirm the margin in your own setup.

Is an auto top off unit safe to leave unattended?

It can be, provided you have a reservoir alarm or backup shutoff and you check the system regularly. Electrical safety matters, so consult a qualified electrician if you are unsure about wiring.

Conclusion

A properly set up auto top off unit keeps salinity steady and saves you from daily manual top-offs. Choose a design that suits your sump, place the sensor in calm water, calibrate carefully, and build in a safety margin. With regular sensor cleaning and periodic salinity checks, your system should run reliably for years.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.