We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Fluval EVO 13.5 Auto Top Off: Setup and Calibration Steps (2026)

Learn how to set up and calibrate a fluval evo 13.5 auto top off system. Covers sensor placement, reservoir setup, calibration steps and common fixes.

Updated November 2026

The fluval evo 13.5 auto top off setup is simpler than most reefers expect, but it rewards a careful install. In this guide you will learn how to prepare the reservoir, position the sensor, calibrate the unit so it adds only fresh water when evaporation drops your level, and fix the handful of problems that tend to show up in the first few weeks. Treat this as a general reference: the exact menu labels and sensor hardware can vary between revisions, so always check the manual that came in your box.

What an Auto Top Off Does on the Fluval EVO 13.5

An auto top off, often shortened to ATO, is a sensor-driven pump that replaces water lost to evaporation. Without one, salinity climbs as pure water leaves the tank and salt stays behind, which stresses corals and fish. The Fluval EVO 13.5 is an all-in-one tank, so its ATO function is built around the tank’s own sump and overflow geometry rather than a separate sump. If you are new to the idea, our general primer on Marine Auto Top Off: How to Set Up and Calibrate an ATO for Reef Tanks explains the logic before you start.

Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).

Before You Start: Tools and Preparation

Gather everything first so you are not stopping mid-install with a dry pump and an open sump. You will need:

  • A dedicated freshwater reservoir with a lid, sized for at least three to five days of evaporation
  • RO/DI water only, never tap water or untreated well water
  • Tubing rated for your pump’s outlet diameter, plus a check valve on the pump line
  • A suction line with a pre-filter or sponge to protect the pump intake
  • A small screwdriver, zip ties, and a bucket for flushing
  • A reliable hydrometer or refractometer to confirm salinity after the first top-off

Plan your reservoir location so it sits higher than the sump’s water line when possible, or use the pump as the only lift. Keep the reservoir close enough that tubing runs stay short, which reduces kinks and air pockets.

Step-by-Step: Installing the Fluval EVO 13.5 Auto Top Off

Step 1: Mount the Reservoir and Pump

Place the reservoir on a stable surface next to the tank, not on the canopy. Fill it with RO/DI water at this stage so you can prime the pump later. Mount the pump in a dry spot close to the reservoir, and keep the electrical connection above any splash zone.

Step 2: Position the Level Sensor

The sensor is the heart of the system. Place it in the sump or the chamber where the water level should be maintained, not in the main display area where surface turbulence or livestock can trigger false readings. Set it so the trigger point sits about one-quarter inch below your intended maximum level. This gives the pump a clear margin before the tank overflows.

Step 3: Run the Tubing

Connect the suction line from the reservoir to the pump intake, then the outlet line from the pump to the sump or tank inlet. Use a check valve on the outlet so water cannot siphon back into the reservoir when the pump is off. Secure every joint with a clamp or tight fit, and route tubing so it cannot loop low enough to trap air.

Step 4: Prime the Pump

Power the pump briefly with the sensor disconnected or tank water deliberately kept high, so the pump runs until water flows steadily through the outlet. Never let it run dry, since most diaphragm and peristaltic designs can be damaged quickly without liquid.

Calibrating the Sensor and Pump Timing

Calibration means teaching the system exactly when to start and stop. Follow this sequence:

  1. Confirm the sensor is seated and the tank is at the target level.
  2. Enable the ATO mode and note the baseline reading if your model displays one.
  3. Lower the water level by a small, measured amount, either by letting it evaporate or by draining a known volume into a container.
  4. Watch the pump start. It should stop once the level returns to the sensor’s set point.
  5. Check the amount added against your expectation. A slightly overshot level is better than a dry sensor.

Setting the Maximum Fill Safety

Always pair the ATO with a second safety measure. Many reefers use a float switch or a secondary cutoff wired to the reservoir so the pump is stopped if the sensor fails in the “on” position. Test this by temporarily raising the sensor reading and confirming the system halts.

Salinity and Water Chemistry Checks

Pure RO/DI water is nearly salt-free, so top-off water is the main reason salinity drifts up over time. Check refractometer readings at least weekly during the first month. If salinity keeps climbing even with proper top-off, you may be losing more water than the sensor is replacing, or the reservoir is contaminated. Keep the reservoir covered to prevent salt creep from airborne salts.

Common Mistakes

  • Using tap water. Tap water adds phosphates, silicates and dissolved solids that feed nuisance algae.
  • Setting the sensor too low. The pump may chase a level that is already close to dry, causing dry-run damage.
  • Skipping the check valve. Without it, the tank can siphon back into the reservoir when power drops.
  • Leaving the reservoir uncovered. Dust, salt creep and debris enter and contaminate the supply.
  • Trusting the sensor blindly. A single float or probe can fail quietly, so monitor the tank level yourself.

Troubleshooting Tips

If the pump runs constantly, check for a stuck sensor, a kinked outlet line, or a reservoir that has run empty and cycled air. If it never starts, confirm power, sensor wiring, and that the reservoir actually contains water. Air in the line usually causes intermittent flow, so re-prime after any tubing work. For broader fault-finding ideas, the general guide JBJ Auto Top Off Not Working: Troubleshooting Steps That Fix It covers similar symptoms and checks that apply across many systems.

Maintenance Schedule

Task Frequency
Check refractometer reading after top-off Weekly
Clean sensor and inspect for film or salt buildup Every two weeks
Inspect tubing and clamps for cracks or leaks Monthly
Clean pump pre-filter Monthly
Test float or backup cutoff Monthly
Replace or refill reservoir and wipe interior As needed, when levels run low or water looks cloudy
  • Refractometer – A refractometer gives you accurate salinity readings that confirm the ATO is keeping your tank stable. Look for a model with a clear scale for reef-range salinity. View on Amazon
  • Reservoir with lid – A sealed reservoir keeps dust and airborne salt out of your top-off water. Choose one that is food-safe and sized for several days of evaporation. View on Amazon
  • Check valve for aquarium tubing – A check valve blocks backflow when the pump stops, protecting the reservoir from siphoning. View on Amazon
  • RO/DI filter cartridges – Pure top-off water is the foundation of a stable ATO setup. Keep spare resin and membranes on hand. View on Amazon

FAQ

Can I use tap water in the fluval evo 13.5 auto top off reservoir?

No. Tap water contains dissolved minerals, phosphates and silicates that build up in the tank over time and fuel algae. Use RO/DI water for every top-off.

How often should I check the reservoir?

Check it at least every few days, and refill before it runs empty. An empty reservoir can cycle air into the pump, which may cause erratic flow or damage a diaphragm pump.

Why does my salinity keep rising even with the ATO running?

Salt creep, an uncovered reservoir, or a reservoir that is accidentally filled with saltwater can all raise salinity. Confirm your top-off water is pure RO/DI and check the sensor is not overfilling.

How do I know if the sensor is calibrated correctly?

Lower the tank level slightly and watch whether the pump starts and stops at the intended points. Compare the level before and after with a clean container to confirm the volume added is reasonable.

Should I add a backup float switch?

Many reefers do. A backup cutoff protects your tank from overflow if the primary sensor fails in the “on” position. Test it regularly.

What if the pump keeps running non-stop?

Check for a stuck sensor, a kinked line, or a leak in the reservoir. Turn the system off, inspect each part, and re-prime before testing again.

Can the auto top off replace daily manual monitoring?

No. The system reduces the work, but you should still visually check water level, salinity and pump operation regularly, and consult your equipment manual or a qualified aquarist if you run into persistent problems.

Conclusion

A well-installed fluval evo 13.5 auto top off keeps evaporation losses under control and holds salinity steady without daily attention. Set up a clean RO/DI reservoir, place the sensor with a sensible margin, calibrate by observing real behavior, and keep a backup safety in place. Monitor your refractometer and tubing on a regular schedule, and the system will do its job quietly for months.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.