We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Neptune Apex Auto Top Off: Setup, Calibration and Fixes for Reef Tanks

Learn how to set up a neptune apex auto top off system, calibrate the float or sensor, avoid salinity swings, and fix the most common reef tank ATO problems.

Updated November 2026

A neptune apex auto top off setup replaces the daily chore of topping off evaporated water with a controlled, automatic system that keeps your reef’s water level and salinity stable. In this guide you will wire the Apex probe and pump correctly, calibrate the level sensing so the pump shuts off at the right point, choose a safe reservoir arrangement, and troubleshoot the problems reefers run into most often.

What the Neptune Apex Auto Top Off Does

The Apex controller monitors a water level probe in your sump or refugium and switches a pump, usually a small RO/DI top-off pump, when the level drops below a set point. Because evaporation removes pure water and leaves salts behind, a reliable ATO is one of the most effective ways to keep salinity from creeping upward. Many reefers pair the ATO with a separate salinity probe so that a failed pump or a stuck float is caught before the tank drifts out of range.

Keep in mind that the Apex is a controller, not a pump. Your system’s behavior depends on the sensor type you choose, the pump’s flow rate, and the safety limits you program. Manufacturers specify that the controller’s outputs should be driven through appropriate relays or a power switching module rated for the pump’s current draw, so check the pump’s specifications before wiring.

Parts and Tools You Need

Gather everything before you start. A tidy build is easier to calibrate and far less likely to leak.

  • An Apex controller with at least one available outlet or digital output channel for the pump
  • A level sensor: either a float switch, an optical sensor, or a probe-style sensor compatible with your Apex configuration
  • A top-off pump rated for the head height and flow you need, typically a low-voltage DC or small AC pump
  • A top-off reservoir filled with RO/DI water, sized for at least several days of evaporation
  • Vinyl or silicone tubing sized to the pump outlet, plus a check valve if your design calls for one
  • A drip loop, cable ties, and a GFCI-protected outlet for all AC components
  • A calibrated refractometer or a digital salinity probe for verifying salinity after setup
  • A marker or painter’s tape to note your target water line

Step 1: Plan the Placement and Sensor Location

Mount the sensor in a quiet area of the sump, away from the return pump’s outflow and from the skimmer’s intake, where turbulence would cause false readings. Position it so the trigger point sits just below the normal water line, roughly a quarter inch to half an inch, so the pump has a small reserve before the level is critical. Route the sensor cable so it cannot be pulled by flow or snagged during maintenance.

Place the top-off reservoir above the sump’s water line if possible. A gravity-fed or siphon-free layout reduces the chance that the pump runs dry or keeps flowing after a failure. If the reservoir must sit lower, use a check valve and confirm that the pump is rated for the lift.

Step 2: Wire the Pump and Sensor to the Apex

Connect the Sensor

Plug the sensor into the appropriate input on the Apex according to your sensor type. Confirm the sensor’s signal in the controller’s status screen before you proceed. A sensor reading that never changes when you lift the float or submerge the probe will cause the entire system to fail.

Connect the Pump

Connect the top-off pump through a relay or switching module compatible with its voltage and amperage. Never run a pump that draws more current than the Apex output or relay is rated to handle. Keep low-voltage and mains wiring separated, and use a GFCI outlet for any AC pump or power supply.

Step 3: Calibrate the Level Sensing

Calibration is where most systems succeed or fail. The goal is a clean on/off cycle that stops the pump at your target level without overshooting.

  1. Fill the sump to your normal operating level and mark the waterline on the glass or with tape.
  2. Lower the water slowly by draining a small amount, or lift the sensor manually, until the controller registers a low-level condition.
  3. Start the pump and watch the water rise. Stop the pump when the level reaches the target mark, and record the sensor state at that point.
  4. Set the controller’s high and low thresholds so the pump turns on at the low point and turns off at the high point, leaving a small deadband to prevent rapid cycling.
  5. Run a full cycle at least twice to confirm that the pump stops reliably and does not overshoot the line.

Set Safety Limits

Program a maximum run time for the pump. Many reefers set a limit that is comfortably longer than a normal top-off event but short enough to stop a flood if the sensor fails to register the high point. Enable any alarm or notification features the Apex offers so you are alerted when the pump runs longer than expected.

Step 4: Verify Salinity and Water Level

Once the system is cycling properly, verify that the top-off water is not changing your salinity. Use a calibrated refractometer or digital probe to test the display tank over several days. Pure RO/DI water raises salinity only by concentrating what remains after evaporation, so a well-functioning ATO should keep readings steady. If salinity climbs steadily, check whether the pump is running longer than necessary or whether the reservoir water is contaminated.

Common Problems and Fixes

Symptom Likely cause What to check
Pump never turns on Sensor not triggering or relay wiring fault Sensor status on controller, relay output, pump power
Pump runs continuously Sensor stuck in the low position or thresholds reversed Float movement, cable damage, calibration values
Overflow or flooding High threshold set too high or sensor fouled Target mark, sensor cleaning, maximum run time
Salinity rising Pump overshooting or reservoir contamination Pump run duration, reservoir water source
Pump cycling rapidly Deadband too small or turbulent water at sensor Threshold spacing, sensor placement

For a more detailed walkthrough of setup problems, see Neptune Auto Top Off Kit: Setup, Calibration and Common Fixes. If you are still choosing a system, Top 3 Neptune Auto Top Off Systems Compared for Reef Tanks compares several options side by side.

Tips and Common Mistakes

  • Using tap water in the reservoir. Tap water adds minerals, silicates, and nutrients that fuel nuisance algae. Use RO/DI water.
  • Skipping the maximum run time. A stuck sensor without a time limit can flood a room in hours.
  • Placing the sensor in turbulent flow. Wave action and return flow cause erratic readings.
  • Letting the reservoir run dry. Check the reservoir weekly and refill before it gets low.
  • Ignoring salinity trends. A slow rise is often the first sign that the pump is overshooting.
  • Skipping periodic cleaning. Salt creep and biofilm on the sensor cause false triggers over time.

If your system behaves differently than described, Apex Auto Top Off: Setup, Calibration and Fixes for Reef Tanks covers additional controller-specific settings.

  • Neptune Systems Apex Controller: The central controller that runs the level logic, safety limits, and alarms for the auto top-off. View on Amazon
  • Neptune Systems Apex Level Sensor: A sensor designed to plug into the Apex input for reliable level detection. View on Amazon
  • Jebao DCP Top-Off Pump: A small submersible pump commonly used for reef top-off duty, sized for low-head reservoir setups. View on Amazon
  • Digital Salinity Refractometer: A tool for verifying salinity after setup so you can confirm the ATO is not raising salt levels. View on Amazon

FAQ

Do I need a separate salinity probe with a neptune apex auto top off system?

It is strongly recommended. A level sensor only tells the controller when to add water, not whether salinity is drifting. A salinity probe provides an independent check that catches pump overshoot or reservoir problems early.

What water should I use in the top-off reservoir?

Use RO/DI water. Tap water and some well water contain dissolved minerals and nutrients that can build up in the tank over time. Store the water in a clean, covered container.

How often should I clean the level sensor?

Inspect it every one to two weeks. Salt creep, algae, and biofilm can cause false readings. Wipe it gently with fresh RO/DI water and check the float or probe movement.

Why does my pump keep running after the water reaches the line?

The high threshold may be set too high, the sensor may be stuck, or the pump may be running longer than the controller’s cutoff. Check the calibration values and sensor movement first.

Can the Apex control more than one pump?

Yes, Apex systems can manage multiple outputs, but each pump needs an appropriate relay or switching module. Confirm the current rating of every output before connecting additional loads.

How much deadband should I leave between on and off levels?

A small deadband, roughly a few millimeters in practice, prevents rapid cycling. Adjust it after observing how the sensor behaves in your sump, since turbulence and sensor type affect the ideal spacing.

What should I do if the reservoir runs empty while I am away?

Use a reservoir large enough for your longest expected absence, and set a low-reservoir alarm if your setup supports one. A dry reservoir with a running pump can damage the pump, so consider a dry-run protection device or a float switch in the reservoir.

Should I consult a professional for electrical work?

If you are unsure about wiring AC pumps, power supplies, or outlets near water, consult a licensed electrician. Mains electricity near aquariums carries real shock risk, and GFCI protection is essential.

Conclusion

A properly calibrated neptune apex auto top off system keeps your reef’s water level and salinity steady without daily attention. Place the sensor carefully, wire the pump through a rated relay, set tight but safe thresholds, and verify salinity over several days. Recheck the sensor and reservoir regularly, and your ATO will serve as a dependable part of your reef’s stability.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.