JBJ Auto Top Off Manual: Setup, Calibration and Safe Use Steps
Need the jbj auto top off manual? Follow these setup, calibration and safety steps to keep your reef tank's salinity stable and your pump running right.
Updated November 2026
A JBJ auto top off manual walks you through installing the unit, setting the water level sensor, and calibrating the pump so it replaces evaporated water without overfilling your sump. Once you have the basics down, you can run the system with confidence and avoid the salinity swings that come from a misadjusted float or sensor. This guide covers the steps in the order most reefers use them.
Before You Start: Gather the Right Tools
Read the manual that came in the box first, because model numbers differ and the sensor layout can vary between the standard and nano versions. Have the following ready so you are not stopping halfway through the install.
Shopping for one? See our guide: 6 Best JBJ Auto Top Off Systems for Reef Tanks (2026).
- Reverse osmosis/deionized (RO/DI) water in a clean container, never tap water
- Silicone-free sealing tape or the mounting hardware included with the kit
- A marker or piece of tape to flag the target water level
- A clean towel and a small cup for spills and priming
- A separate test kit or refractometer for checking salinity after the first fill
Installing the Reservoir and Sensor
Place the RO/DI reservoir above the sump so gravity can help feed the pump, and keep the tubing short and free of sharp kinks. Mount the sensor in the sump at the level you want the water to stop, usually a fraction of an inch below your overflow box’s drain point. Route the sensor cable so it cannot be pulled into the return pump or caught in the skimmer.
Calibrating the Water Level
Calibration sets the exact point where the pump starts and stops. Work through it in this order:
- Confirm the reservoir is full of RO/DI water and the pump is primed, with no air in the line.
- Fill or let the sump settle to your normal operating level, then mark it on the glass.
- Adjust the sensor height so it sits just below the mark, leaving a small buffer to prevent short cycling.
- Watch one full top-off cycle. The pump should stop before the water rises above your mark.
- Repeat the check the next day. Small changes in evaporation can shift the level slightly.
Running Safe Top Offs Day to Day
A correctly calibrated unit still needs periodic attention. Check that the reservoir has enough RO/DI water, and keep the sump’s evaporation rate in mind when you change room temperature or lighting. Many owners also add a secondary float switch or a simple low-water alarm so a dry reservoir or stuck sensor does not go unnoticed for days.
Watching Salinity After a Fill
Because the unit adds only fresh water, salinity rises over time as salt stays behind. Test salinity at least weekly and adjust with fresh water when the reading climbs. Refractometers and digital meters both work, provided they are calibrated.
Recommended gear
- A replacement return or dosing pump designed for ATO duty helps when the stock pump struggles with long tubing: View on Amazon
- A digital refractometer gives quick, consistent readings after each top-off: View on Amazon
- A backup float or low-level alarm guards against a failed sensor: View on Amazon
Common Mistakes
- Using tap water in the reservoir, which introduces minerals and nutrients that cause algae and salinity drift
- Setting the sensor at the overflow line, leaving no margin before the sump overflows
- Skipping calibration after changing sump volume, rock, or equipment
- Letting the reservoir run dry without a low-level warning
- Forgetting to clean the sensor, which can cause false readings from salt creep
For a deeper walkthrough of the same process, see JBJ Auto Top Off Setup: Step-by-Step Guide for Reef Tanks. If the pump runs but the level does not hold, JBJ Auto Top Off Not Working: Troubleshooting Steps That Fix It covers the most common causes.
FAQ
How often should I check the reservoir?
Check it at least every few days, and more often in warm rooms or with high-evaporation setups. Keeping a visible level mark on the reservoir makes this a quick glance.
Can I use tap water with the unit?
No. Tap water carries dissolved solids that build up in the sump and change salinity and nutrient levels. Use RO/DI water.
What if the pump keeps running after the level is correct?
Recheck the sensor height and make sure it is not fouled with salt residue. If the problem continues, consult the manufacturer or an experienced reefer, since a stuck sensor can cause overflows.
Conclusion
With the reservoir placed correctly, the sensor calibrated to your mark, and a regular check on salinity, a JBJ auto top off system will keep your reef stable without daily attention. Re-verify the level after any equipment change. A few minutes of setup now prevents the salinity swings and overflows that cause the most trouble.
Related reading
Ready to choose one?
