We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Avast Auto Top Off: A Step-by-Step Guide for Reef Tanks

Learn how an avast auto top off works, how to set it up and calibrate it, and how to avoid the mistakes that cause salinity swings in your reef tank.

Updated November 2026

An avast auto top off is a device that monitors your reef aquarium’s water level and adds fresh water or RO/DI water to replace what evaporates, keeping salinity stable between your manual water changes. In this guide you will learn how to choose the right setup, install it safely, calibrate the sensor, and troubleshoot the problems that most often cause overfilling or dry-run events. Work through the steps in order and you should end up with a system that tops off reliably without you watching it every day.

What an Auto Top Off Does and Why Reef Tanks Need One

Evaporation removes pure water and leaves salts behind. In a typical reef system, the water level can drop a few millimeters a day, and that gradual loss concentrates salinity over time. Manual top-off with a pitcher works, but it is easy to forget on a busy week, and a mistake of a single gallon can shift salinity noticeably in a small tank. An automatic top-off system closes that gap by sensing the water level and running a pump or valve only when needed.

Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).

The term “avast auto top off” is commonly used by hobbyists looking for a float- or sensor-based ATO that connects to a sump or refugium reservoir. Whatever brand you use, the principles below apply: a sensor, a controller or float switch, a pump or solenoid, a fresh-water reservoir, and a safety shutoff.

Parts and Tools You Will Need

Before installation, gather everything so you are not stopping halfway through. Most setups require:

  • The ATO controller, sensor or float assembly, and any included mounting hardware
  • A dedicated RO/DI water reservoir, ideally a food-safe container with a lid
  • A pump or solenoid valve rated for the head height between reservoir and sump
  • Vinyl or silicone tubing sized to the pump outlet (commonly 1/4-inch or 3/8-inch ID)
  • A GFCI-protected outlet or power strip, and a drip loop for all cords
  • Painter’s tape or a marker for tracing the water line
  • A refractometer or calibrated hydrometer, and a clean cup for testing
  • Aquarium-safe silicone or zip ties for securing tubing

Step 1: Choose the Right Reservoir and Water Source

Top-off water should be RO/DI, never tap water and never plain salt water. Tap water adds minerals, chlorine residue, and silicates that build up in the tank. Use a reservoir large enough to last at least a week at your evaporation rate. For a 75-gallon reef losing about 1/2 inch per week, a 5-gallon jug is usually sufficient, but a 10-gallon reservoir gives you more margin. Keep the reservoir covered to prevent algae growth and dust contamination, and keep it lower than the sump’s maximum water line so gravity cannot siphon water into the tank.

Step 2: Mount the Sensor or Float at the Correct Height

Placement determines accuracy. Mount the sensor in a calm area of the sump, not in the return pump intake and not where bubbles from a protein skimmer collect. Position it so the sensing point sits about 1/4 inch below your desired water line. Waves and surface agitation can cause false readings, so reduce surface movement if possible or place the sensor behind a baffle. Secure the mounting bracket firmly, but do not drill or modify the sump without checking the manufacturer’s instructions first.

Step 3: Install the Pump or Valve and Route Tubing

Run the outlet tubing from the reservoir to the sump. Keep the tubing as short as practical and avoid sharp kinks, which reduce flow and can cause the pump to strain. Place the pump so it stays submerged in the reservoir or sits just above its water line, following the manufacturer’s guidance. If you use a solenoid valve, mount it on a dry, stable surface above the sump’s maximum level. Add a check valve or anti-siphon loop where specified to stop back-flow if power fails.

Step 4: Calibrate the Controller

Calibration sets the shutoff point so the system stops before the sump overflows. Follow these sub-steps:

Set the Water Line

Fill the sump to your normal operating level. Mark the exact water line with tape. Confirm that the sensor is submerged to its intended depth and that the reading on the controller, if it has a display, is steady.

Run a Dry-Fire Test

Briefly lower the water level or lift the float manually. Verify that the pump starts and that the controller responds. Then raise the level again and confirm the pump stops at the correct point. If the system overshoots, adjust the sensitivity or float position and repeat.

Check Overflow Margin

Make sure there is at least 1/2 inch of freeboard between the shutoff point and the sump’s overflow. This buffer covers splash, surge from the return pump, and small sensor delays.

Step 5: Verify Salinity Stability Over the First Two Weeks

Once the system is running, test salinity regularly. Use a refractometer or calibrated hydrometer and record readings in a log. Expect small fluctuations, but a steady salinity range should appear within a few days. If salinity climbs over time, the system may be adding too little fresh water, or your reservoir may be contaminated. If salinity drops, check for leaks, a stuck valve, or the pump running continuously.

Common Mistakes to Avoid

  • Using tap water or unpurified water. This introduces contaminants and creates long-term problems.
  • Mounting the sensor in turbulence. False readings cause constant cycling or missed top-offs.
  • Skipping the overflow buffer. A sensor that triggers at the very top of the sump invites overflow during surges.
  • Ignoring the reservoir. An empty jug means a dry pump and possibly a dry sump. Set a reminder to refill.
  • No power protection. Plug the controller and pump into a GFCI-protected outlet, and use a drip loop.
  • Forgetting to clean the sensor. Salt creep and biofilm change readings over time, so inspect and rinse it monthly.

Troubleshooting Quick Tips

Symptom Likely Cause Fix
Pump runs continuously Sensor not detecting water or stuck in the “on” position Clean sensor, check wiring, recalibrate
Sump overflows Shutoff point set too high or valve stuck open Lower the shutoff point, inspect the valve
Salinity rising steadily Not enough fresh water added Check reservoir level, pump output, and tubing
Pump cycles rapidly Surface agitation or sensor too sensitive Relocate sensor, reduce sensitivity

A reliable RO/DI source matters more than any single accessory, but these items make an ATO setup easier to maintain.

  • Tunze Osmolator 3155 Auto Top Off System: A widely used controller with a sensitive probe that suits many reef sumps. View on Amazon
  • Neptune Systems Apex Controller: Useful for owners who want to monitor water level and other parameters from one screen. View on Amazon
  • Vinyl aquarium tubing, 1/4-inch ID: A common size for ATO outlets that is easy to route and cut. View on Amazon
  • Food-grade RO/DI reservoir with lid: Keeps top-off water clean and covered between refills. View on Amazon

For more model-specific setup advice, see Tunze Osmolator 3 Auto Top Off: Setup and Calibration Guide and Top 6 Auto Top Off Reef Systems Compared for Reef Tanks (2026). If you run a nano tank, Red Sea Max Nano Auto Top Off: Setup and Calibration in 7 Steps covers the smaller-footprint approach. Problems with a float that will not respond are covered in JBJ Auto Top Off Not Working: Troubleshooting Steps That Fix It.

FAQ

Can I use tap water in an auto top off?

No. Tap water contains dissolved minerals, silicates, and sometimes chlorine or chloramine, which accumulate in the tank and can fuel algae or interfere with coral growth. Use RO/DI water for all top-off.

How often should I clean the sensor?

Inspect the sensor every two to four weeks. Rinse it in fresh RO water and wipe away salt creep or biofilm. Clean sensors give more accurate readings and fewer false triggers.

How much freeboard should I leave above the shutoff point?

Aim for at least 1/2 inch between the shutoff level and the sump overflow. Larger sumps with strong return flow may need more margin.

Why does my auto top off keep running?

Common causes include a sensor that is not submerged, a stuck valve, a float that is misaligned, or a reservoir line that has pulled air. Check each one before recalibrating.

Can an ATO replace water changes?

No. An ATO only replaces evaporated water. Regular partial water changes are still needed to replenish trace elements, remove nutrients, and maintain overall water quality.

What happens if the reservoir runs empty?

The pump will run dry, which can damage it. Keep an eye on reservoir level, and consider a low-level alarm or a float switch on the reservoir itself.

Do I need a GFCI outlet for an ATO?

A GFCI-protected outlet is strongly recommended because the system operates near water. Always follow manufacturer electrical guidance, and consult a qualified electrician if you are unsure about your wiring.

Conclusion

A well-installed avast auto top off keeps salinity steady and removes one of the most common sources of reef tank stress. Mount the sensor in calm water, calibrate with a safe overflow buffer, and use only RO/DI water in the reservoir. Test salinity for the first couple of weeks, then check the system regularly so small issues do not turn into big ones.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.