We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Set Up Auto Top Off for a Reef Tank: 7 Steps to Stable Water Levels

Learn how to set up auto top off for your reef tank in 7 steps, from placing the sensor to calibrating the pump and testing for leaks.

Updated November 2026

To set up an auto top off (ATO) system, you mount a reservoir of RO/DI water, place a float or optical sensor at the correct water level, plug the pump into the controller, and calibrate the shutoff point. Done right, the system keeps your reef tank topped off automatically, so evaporation no longer drops salinity or exposes equipment. This guide walks through each step in order.

What You Need Before You Start

Gather everything before you touch the sump. A clean setup takes about an hour once the parts are in hand.

Shopping for one? See our guide: 6 Best Aquarium Auto Top Off System Picks for Reef Tanks (2026).

  • A dedicated reservoir filled with RO/DI water, sized for at least several days of evaporation
  • An ATO pump rated for your tank’s evaporation rate and head height
  • A sensor (float switch, optical sensor or conductivity probe, depending on your kit)
  • Vinyl tubing that fits the pump outlet and the sump inlet
  • A drip loop, check valve and cable ties
  • A way to mark the reference water line, such as painter’s tape

Step-by-Step Installation

1. Choose the reservoir location

Place the RO/DI reservoir higher than the sump’s top water line, or use a pump rated for the lift. Keep it out of direct light to limit algae growth inside the container.

2. Mount the sensor in the sump

Position the sensor in a calm area, away from the return outlet and skimmer intake. Turbulence causes false readings. Set it so the trigger point sits about a quarter inch above your normal water line.

3. Run the tubing and drip loop

Route the tubing from the reservoir pump to the sump, then create a drip loop above the water line. The loop stops siphoning if the pump fails in the “on” position. Add a check valve on the reservoir side if your model lacks one.

4. Plug in and set the controller

Connect the sensor and pump to the controller according to the manufacturer’s wiring diagram. Make sure the reservoir pump is on a separate outlet from your heaters and return pumps, so a single fault cannot disable everything at once.

5. Calibrate the shutoff point

Fill the sump to your normal level and mark it. Run the pump manually until the water reaches the sensor’s trigger height, then confirm the pump stops at the mark. Adjust the sensor height or the controller’s threshold until the pump shuts off within a few millimeters of your reference line.

6. Test the failsafe

Simulate a stuck-on condition by unplugging the sensor or lifting the float. The controller should cut power to the pump. Many owners report testing this monthly, since a silent failure is the most common cause of flooding.

7. Monitor the first week

Check the sump daily for the first few days. Confirm the level holds steady and the reservoir drops at a rate that matches your evaporation. Log the reservoir level so you notice a sudden change.

Common Mistakes to Avoid

  • Using tap water or unpurified water in the reservoir, which raises nitrate and salinity over time
  • Placing the sensor too close to a return outlet, causing false triggers
  • Skipping the drip loop, which allows siphoning if the pump runs continuously
  • Plugging the pump into the same outlet as your heater or return pump
  • Forgetting to refill the reservoir, so the system runs dry and the pump burns out
  • Tunze Osmolator 3155 series: a common choice for reef owners who want a well-documented controller with dependable sensing, which many owners report simplifies calibration. View on Amazon
  • Reef Octopus ATO kit: a budget-friendly option whose included tubing and sensor make a complete starter setup. View on Amazon
  • Vinyl tubing with check valve: prevents backflow and keeps the reservoir line clean and easy to inspect. View on Amazon

FAQ

How often should I check my auto top off system?

Check the reservoir and sump level at least weekly. Test the failsafe monthly by simulating a stuck-on condition.

Can I use tap water in an ATO reservoir?

No. Use RO/DI water, because tap water adds minerals, nitrates and phosphates that build up in a reef tank over time.

Why does my ATO keep running when the water level is correct?

The sensor is likely misplaced or fouled. Move it away from turbulence, clean it, and recalibrate the shutoff point.

Conclusion

A properly calibrated auto top off keeps salinity stable and protects your equipment from dry running. Work through each step, test the failsafe, and monitor the system for the first week. For model-specific steps, see Auto Top Off Unit for Reef Tanks: 7 Steps to Set It Up Right and Marine Auto Top Off: How to Set Up and Calibrate an ATO for Reef Tanks.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.