We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

JBJ Auto Top Off Instructions: Step-by-Step Setup for Reef Tanks

Follow these jbj auto top off instructions to mount, plumb, and calibrate your JBJ ATO so your reef tank stays at the right level without daily babysitting.

Updated November 2026

JBJ auto top off instructions come down to four jobs: mount the reservoir and sensor, plumb the pump, set the float or sensor height, and test the system before you walk away. Done correctly, your reef tank will top off with RO/DI water automatically and shut the pump off before it overflows or runs dry. The steps below follow the general setup flow used across JBJ’s ATO models, but always check the manual that came in your box for model-specific details.

What You Need Before You Start

Gather everything first so you are not stopping halfway through with wet hands and an open sump.

Shopping for one? See our guide: 6 Best JBJ Auto Top Off Systems for Reef Tanks (2026).

  • The JBJ ATO reservoir, pump, and sensor or float assembly
  • Tubing matched to the pump outlet (usually 1/4-inch or 3/8-inch silicone or vinyl)
  • A way to secure the reservoir above the sump’s water line
  • RO/DI water in the reservoir, never tap water
  • A marker or tape to note your water level
  • A dry paper towel and a small cup for priming

Step 1: Mount the Reservoir and Sensor

Place the reservoir on a stable surface or hang it on the tank stand, high enough that the pump can lift water from it. Mount the sensor or float inside the sump or refugium where it will sit in the water at your target level. Keep the sensor away from the return pump’s flow and from the skimmer’s bubbles, since turbulence causes false readings.

Positioning tips

  • Keep the sensor in calm water, typically at a spot where it won’t bump against rock or fittings.
  • Route the sensor cable so it cannot be pinched by the sump lid.
  • Leave enough slack on the pump’s power cord to reach a dedicated outlet.

Step 2: Plumb the Pump and Set Your Water Level

Connect the pump outlet to the tubing and run it into the sump, ideally above the waterline with a short drip path rather than a submerged end. Fill the reservoir with RO/DI water and prime the pump by submerging the intake and powering it briefly until water flows steadily through the tubing. Once the sump is at its normal operating level, mark that spot on the sump glass. Then adjust the sensor so it triggers the pump when water drops about 1/8 inch below the mark, and cuts power when the level returns to the line.

Step 3: Calibrate and Test the System

With the pump running, watch the sump level rise to the mark and confirm the pump shuts off on its own. Lower the level by a small amount, or lift the sensor manually, to confirm the pump starts. Repeat this test two or three times. Many owners recommend a 24-hour observation period before leaving the system unattended, because evaporation rates vary with room temperature and tank lighting.

  • Silicone tubing for ATO lines: Flexible and resistant to saltwater creep, it makes clean runs easier to route. View on Amazon
  • Reservoir mounting bracket: Keeps the RO/DI container stable and above the sump’s water line. View on Amazon
  • Digital thermometer: Lets you track temperature changes that affect evaporation and sensor readings. View on Amazon

Common Mistakes

  • Filling the reservoir with tap water, which leaves mineral deposits on the sensor and pump.
  • Placing the sensor in the skimmer’s bubble stream, causing erratic pump cycling.
  • Skipping the priming step, leaving the pump to run dry and wear out faster.
  • Setting the reservoir too low, so the pump cannot lift water and stalls.
  • Forgetting to check the reservoir weekly, which can leave the system running dry.

For a broader walkthrough, see JBJ Auto Top Off Setup: Step-by-Step Guide for Reef Tanks. If your system is already installed but misbehaving, JBJ Auto Top Off Not Working: Troubleshooting Steps That Fix It covers the most common causes.

FAQ

Can I use tap water in a JBJ auto top off reservoir?

No. Tap water contains dissolved minerals that build up on the sensor and pump and can raise your tank’s salinity over time. Use RO/DI water only.

How often should I check the reservoir?

Check it at least once a week and refill before it runs low. Many owners keep a backup reservoir sized for several days of evaporation.

Why does the pump keep running after the water reaches the mark?

The sensor is usually set too high or sitting in turbulent water. Reposition it into calmer flow and retest the shutoff point, following your model’s manual for adjustment.

Conclusion

With the reservoir secured, the pump primed, and the sensor calibrated to your marked level, a JBJ auto top off can keep your reef stable day after day. Run the test cycles, use only RO/DI water, and check the system weekly. For a model-specific walkthrough, consult the manual that came with your unit or a qualified reef professional.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our reef & saltwater aquariums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for My Reef Aquarium.